WG K7000 need help left side shadow lines

Trennel

New member
Joined
Jul 16, 2012
Messages
19
Reaction score
0
Location
2605, Denmark
have does lines for sometime now and only left side, still there after a capkit and a new flyback, the colors looks good, but what did I missed , please help me with the problem , If u know what cause it :confused:

WG 25" k7000

img0423qq.jpg
 
have any other pics?? Its pretty common for c56 or c57(cannot remember offhand) to go bad and cause vertical bars on the lefthand side. Might want to recheck and maks sure that one got changed.
 
The Intro was going fast, so don´t mind the picture ;), but its visible in blue and black as I see it, not in bright colors

img0425aj.jpg
 
hmmm have replaced C56 and C57. but maybe the caps are born bad, should I go fetch c56:22uF,160v and c57:47uF 160, just if other caps can cause it?
 
more pictures of board, had to wait, my son was playing ;) did not resize pictures for better quality
img0430gv.jpg

img0429uu.jpg

img0428ga.jpg

img0427hr.jpg
 
To be honest with you bro, I would just shotgun the whole chassis with a complete capkit, as oppose to just trying to select which one is bad. A capkit is never a bad idea, as long as you do not mess it up. You sound like you are comfortable messing with monitors, so I would cap the whole thing before I did anything else.
 
To be honest with you bro, I would just shotgun the whole chassis with a complete capkit, as oppose to just trying to select which one is bad. A capkit is never a bad idea, as long as you do not mess it up. You sound like you are comfortable messing with monitors, so I would cap the whole thing before I did anything else.

He just did thats the issue. Now did he get bad caps or is there something else wrong?


Id shotgun those two caps with something you know is good and recheck back. TO be honest i have more then one game with the same issue and im not going to bother until it either gets much worse or the monitor pukes completely.

Looks like yours used to have the daughterboard hooked up. Chassis might have originally been for a 27".... is your monitor a 25" or 27" ?

Also there was someone not too long ago that came to the conclusion that thier gameboard was causing this issue. Weird. It might be worth your time to clean the edge connector of your boardset just in case.
 
Last edited:
blaah Unlucky me :( I solder all the spots then I sudenly have vertical Collaps WHYYYYY ME, I have 21,3VDc over pin1 and pin6 on IC3 is it enough? or what?
 
Well After some minutes it says 24,9vdc (pin1 and pin6) is it then the IC3 I need to replace if I have the voltage?
 
some more testing, R80 is BAD , looks like its a 5.6 ohm, hard to see the colors on the resistor
 
Its alive ALIIIIIIIVE ;) , went to my local electronics, a new R80 and some caps, changed c56,57,50. still have some shadows in left side, but I might have to live with it.
 
Alive is good, now for a hard question.

Did you match the polarity marks of the removed caps with the installed caps?

It does make a difference. I saw some stuff on this board that looked like maybe a cap was flipped, but I don't have one of these in the shop or house to compare it with, so I'm not sure.
 
Alive is good, now for a hard question.

Did you match the polarity marks of the removed caps with the installed caps?

It does make a difference. I saw some stuff on this board that looked like maybe a cap was flipped, but I don't have one of these in the shop or house to compare it with, so I'm not sure.

Yeah, my next mission would be to go over all of the caps you replaced and make sure none are in backwards.
 
need some help on neckboard r213 is it a 68ohm on 25K7195? cause the one I have looks like its bad (my multimeter goes up and down to infinti)and can that be the shadow problem??
 
Last edited:
Back
Top Bottom