Star Wars - How much is this worth ?

When I saw it there was some type of leakage that came from the controls that where on the CP , don't know what that was .
 
When I saw it there was some type of leakage that came from the controls that where on the CP , don't know what that was .

550 for a non working game and he can't believe it either.Not willing to negotiate. I don't care what it is, there are only about 3 or 4 titles i'd pay that much for, star wars ur ain't one of them. Cockpit is another story
 
Someone on here bought a minty 1 in the DC area not long ago that didnt work after being moved. Paid $250.00 and got it home and found a loose cable if I remember right? The Vector monitors aren't cheap 2 fix so keep that in mind.
 
I sent him an email @ 8:14am stating I would take it.

If I had his cell # I would call him as well.

Fingers crossed!

#1 I have wanted one for quite some time.
#2 I would not have to add a flight yoke to my Multi Vector project! (That headake alone is worth $500) :)
 
Last edited:
I sent him an email @ 8:14am stating I would take it.

If I had his cell # I would call him as well.

Fingers crossed!

#1 I have wanted one for quite some time.
#2 I would not have to add a flight yoke to my Multi Vector project! (That headake alone is worth $500) :)


PM sent ......
 
When I saw it there was some type of leakage that came from the controls that where on the CP , don't know what that was .


If the leakage was a black sticky substance its the rubber washers behind the yoke have melted from the game being stored some place very hot! The game could be worth 550 or even 600 if it has the amplifone monitor. Don't know if I would pay that price for it with a wells. You gotta take that into consideration for value. If its gotta wells you gotta see if the spot killer is on if so then it could be the VGchip is bad or something else like chasis transistors or the low voltage section. If its got the amp and no neck glow then its probably the big red or issues on the deflection board. Just dropping my opinion, good luck to whoever gets it.

Joe(acejedi)
 
Someone on here bought a minty 1 in the DC area not long ago that didnt work after being moved. Paid $250.00 and got it home and found a loose cable if I remember right? The Vector monitors aren't cheap 2 fix so keep that in mind.

Uh, vector monitors are about as inexpensive to fix as raster... it's called a cap kit. About $15.00. Of course you'd be wise to install a LV2000/LV6100 which is another $30 or so I think. Still, vectors monitors aren't super expensive to fix as some assume.

EDIT: WG vectors are cheaper...but even Amp vectors aren't too expensive to fix any more... though a bit more so than WG usually.
 
I have been offered 2 fully working excellent condition star wars uprights for $400 each in the past year. $550 is way too much IMO for a SW that plays blind. At least out here in CA it is. I would say $200-$300 if the cab is in good condition.
 
I have been offered 2 fully working excellent condition star wars uprights for $400 each in the past year. $550 is way too much IMO for a SW that plays blind. At least out here in CA it is. I would say $200-$300 if the cab is in good condition.

Considering they are worth about $1000 out here fully working in nice cabinets, they are worth buying and shipping for free to somewhere else in the US as part of a greater sales price. It seems like you guys are on a different planet with your 10% sales tax and $400 Star Wars. :001_ssuprised:
 
Considering they are worth about $1000 out here fully working in nice cabinets, they are worth buying and shipping for free to somewhere else in the US as part of a greater sales price. It seems like you guys are on a different planet with your 10% sales tax and $400 Star Wars. :001_ssuprised:

I don't think so. Dan is on a different planet. I have never seen a fully working one go for less than $1000 around here. It must be someone he knows who is just hooking him up. I don't know. Dan, shed some light on how you find these great deals! ;)
 
I have come across one Star Wars down here in the last 2 years and it was non-working and the seller wanted $1000, didn't even play blind. Now that was outrageous.

If the cab is in good shape I would pay it. Board repairs are alot more then monitor repairs and honestly any vectors are rare around me.
 
I got my upright ESB with a dead monitor for 300.00 repaired the chasis for 50.00 and its all good! Deals are out there. Hey Dan if you still got the hook up on those 2 uprights ill take both for 800.00!

Joe(acejedi)
 
I got my upright ESB with a dead monitor for 300.00 repaired the chasis for 50.00 and its all good! Deals are out there. Hey Dan if you still got the hook up on those 2 uprights ill take both for 800.00!

Joe(acejedi)

I'm pretty sure they have been sold as they were offered to me 4 or 5 months ago.
 
Back
Top Bottom