FS Parts: Sanyo EZ-V sales thread - Bay Area, CA

DuffCon

Well-known member

Donor 4 years: 2015, 2021, 2024-2025
Joined
Apr 9, 2015
Messages
4,193
Reaction score
2,770
Location
California
Rating - 100%
18   0   0
Background Thread:


Gents, I'm proud to offer the first of my truckload of EZ-V monitors. Hopefully this is the missing piece for someone rebuilding a Nintendo cab.

Out of the 6, I picked this one to do first as it is the only complete monitor with AMP/Inverter board out of all 6. It's been outside for a long time, and was covered in dirt and spiders. All the frames were rusty and gross, so I de-rusted and painted the frame components. Is this factory fresh? No, but it's pretty good for something you won't every look at.

I've done a lot of chassis, so all the normal stuff has been done, reflow input header, cleaned up the flux mess, Deoxit on the pot, etc.

Tested the tube and gave it 1 round of 'clean and balance' looking crisp and bright.

The chassis has been rebuilt with Arcade Parts and Repair's cap kit and b+ set to 108vdc

I also rebuilt the amp. Have not tested a signal, but have hooked up a speaker and confirmed the Nintendo hum and the volume pot works.

Ran in on the test bench for 5 hours. Everything is great.

Willing to ship, my last monitor cost around $120 to ship for postage and materials to the great lakes area from California. I basically get the heavy duty box from home depot and cut a piece of 1/2" plywood to fit, as described in this thread:


The market for whole monitors is weird, so I will make this a MMAO, obviously understand that I probably have 5-6 hours of work on this one monitor. Not trying to retire on Sanyo refurbishment, but you get the point.

Also, if you are using this for a Nintendo game it does not need the inverter board and I'd prefer to keep it if you don't need it, we can work that into the price.
 

Attachments

  • IMG_4054.jpeg
    IMG_4054.jpeg
    581.5 KB · Views: 47
  • IMG_4053.jpeg
    IMG_4053.jpeg
    544.6 KB · Views: 48
  • IMG_4052.jpeg
    IMG_4052.jpeg
    581.7 KB · Views: 47
  • IMG_4051.jpeg
    IMG_4051.jpeg
    511.7 KB · Views: 44
  • IMG_4050.jpeg
    IMG_4050.jpeg
    502.6 KB · Views: 43
  • IMG_4049.jpeg
    IMG_4049.jpeg
    602.5 KB · Views: 44
  • IMG_4107.jpeg
    IMG_4107.jpeg
    449.1 KB · Views: 8
  • IMG_4110.jpeg
    IMG_4110.jpeg
    498.7 KB · Views: 10
Last edited:
More pics: (60-1 & Pandora's box)
 

Attachments

  • IMG_4027.jpeg
    IMG_4027.jpeg
    532.9 KB · Views: 28
  • IMG_4026.jpeg
    IMG_4026.jpeg
    392.4 KB · Views: 28
  • IMG_4020.jpeg
    IMG_4020.jpeg
    616 KB · Views: 28
Requested burn pic:
 

Attachments

  • IMG_4055.jpeg
    IMG_4055.jpeg
    304.1 KB · Views: 27
did some more tweaking and it's giving a great picture. Better with a real PCB.
 

Attachments

  • IMG_4084.jpeg
    IMG_4084.jpeg
    787.7 KB · Views: 20
Recently, there have been some non-restored EZs that have sold on eBay for $400+shipping.

I'd rather deal with a member here than eBay, so I'd sell for considerably cheaper, basically make me an offer.

Also note there is a couple of small scratches that you can see in the last pic, just pointing that out in case you didn't see it.
 
Here's #2. Just recapped, reflowed header and other cold parts, bath, etc. this frame is the least rusted of all so I left as is. I have a HV cage if you want, but it is a bit rusty.

This is the version with a manual degauss button

I do not have a working inverter board. The 16v wire is clipped in this chassis, so if you wanted to add one (sold on mikes arcade) you would need to patch the wire.

this is also missing the amp, so you will need to obtain one or use an after market solution.

Neckboard has a protector, not pictured.

Tube was tested and given 1 round of rejuvenation and it looks great. Almost no burn that I can see, a couple of small scratches, not really noticeable unless you're really OCD.

I'm looking for $300 plus shipping. So far it's ranged from $70 to Washington and $110 to the Great Lakes area.

Please understand that it takes many hours to wash and repair, not to mention constructing the shipping box. Etc. Im open to offers or partial trades, PC10, MVS, or chassis for repair.
 

Attachments

  • IMG_4145.jpeg
    IMG_4145.jpeg
    639.4 KB · Views: 24
  • IMG_4146.jpeg
    IMG_4146.jpeg
    604.8 KB · Views: 25
  • IMG_4147.jpeg
    IMG_4147.jpeg
    480.2 KB · Views: 27
  • IMG_4152.jpeg
    IMG_4152.jpeg
    564.6 KB · Views: 25
  • IMG_4154.jpeg
    IMG_4154.jpeg
    619.3 KB · Views: 22
Packaging update:
 

Attachments

  • IMG_4183.jpeg
    IMG_4183.jpeg
    457.2 KB · Views: 23
  • IMG_4177.jpeg
    IMG_4177.jpeg
    630.9 KB · Views: 16
#3 is burning in. This one got a new B+ pot and caps (obviously) The tube is mostly without burn, but does have some light scratches. This is the best of what's left. The remaining 2 tubes have medium DK3 & playchoice burn. @RobertL
 

Attachments

  • IMG_4223.jpeg
    IMG_4223.jpeg
    637.3 KB · Views: 7
  • IMG_4215.jpeg
    IMG_4215.jpeg
    649.3 KB · Views: 7
  • IMG_4216.jpeg
    IMG_4216.jpeg
    787.5 KB · Views: 6
  • IMG_4240.jpeg
    IMG_4240.jpeg
    622.2 KB · Views: 6
  • IMG_4241.jpeg
    IMG_4241.jpeg
    728.7 KB · Views: 6
  • IMG_4243.jpeg
    IMG_4243.jpeg
    597.2 KB · Views: 6
  • IMG_4244.jpeg
    IMG_4244.jpeg
    527.4 KB · Views: 6
Back
Top Bottom