Sanyo 20EZ Neck PCB Trimmer Pot Kit Part Numbers?

[ChanceKJ]

Anyone have Mouser part numbers for the five neck board trimmer pots on a Sanyo 20EZ?

I'm doing a Mouser order for some other things and I just can't narrow down the exact 500 and 10K ohm pots I need that fit.

 

[87 t-66]

All you should need is a (metric) ruler and the datasheets on mouser. Each part datasheet has very precise measurements you can use to find exactly what you need.

 

[ChanceKJ]

All you should need is a (metric) ruler and the datasheets on mouser. Each part datasheet has very precise measurements you can use to find exactly what you need.

I'm sorry, but thats just not helpful at all.

I've been staring at data sheets for 2 hours today trying to whittle down something that matches the same 5x5mm measurements. For example, I know AP&R uses Amphenol Piher brand pots, but nowhere in the PT6 data sheet does it have a variable for the middle 5mm wiper pin.

It makes no sense to me to go to AP&R, spend $11.14 USD, plus an extra $3.86 for random parts I dont need to get to the minimum order of $15, PLUS and extra $38.34 in shipping, totalling $53.34 USD, which is $72.25 Canadian for 5 little pots that I can get for about 0.85 cents Canadian each on an order I'm already paying for shipping on.


...So, if ANYONE has ordered these from Mouser/Digikey/Etc... regardless of the brand, and knows they work to replace the neck board pots in a 20EZ, I would love to hear from you.

 

[87 t-66]

I'm sorry, but thats just not helpful at all.

Huh? lol.

Go here: https://www.digikey.com/en/products/filter/trimmer-potentiometers/80?s=N4IgjCBcoGwJxVAYygFwE4FcCmAaEA9lANogAsYYAHHAOwgC6+ADqlCAMoYCWAdgOYgAviKA

Measure the pots you are trying to replace and filter the results. Then you can probably use the same physical size and just change resistance as needed. Look at the data sheets to confirm.

 

[ChanceKJ]

Huh? lol.

Go here: https://www.digikey.com/en/products/filter/trimmer-potentiometers/80?s=N4IgjCBcoGwJxVAYygFwE4FcCmAaEA9lANogAsYYAHHAOwgC6+ADqlCAMoYCWAdgOYgAviKA

Measure the pots you are trying to replace and filter the results. Look at the data sheets to confirm.

Yes.

I've been doing that. I'm not finding anything. They obviously exist because a few arcade places in the US sell them. Trying to get me to help me to help myself by pointing me in the direction I'm already going is not helpful. Thats like standing West of Fayetteville, NC, asking someone for directions to a specific address in Charlotte, NC, and them answering by just point WEST. Thats what I mean by "Not helpful". lol

 

[SNESNESCUBE64]

You can probably make a Piher PT10 work with those.

 

[ChanceKJ]

You can probably make a Piher PT10 work with those.

(Head South on Robeson St until it turns into the 401. Then head West for about 2 hours along the 144, and the 74. That will at least get you to Charlotte, but unfortunately I don't know that exact neighbourhood)

See now THATS a competent lead.

Yes, Thank you, the P-10 series seems to have a 5mm pitch to the wiper pin. I'll dig a little deeper and find them.

 

[SNESNESCUBE64]

See now THATS a competent lead.

Yes, Thank you, the P-10 series seems to have a 5mm pitch to the wiper pin. I'll dig a little deeper and find them.

https://www.digikey.com/en/products/filter/trimmer-potentiometers/80?s=N4IgjCBcoEwCxVAYygMwIYBsDOBTANCAPZQDaIcADDAGxgwgC6hADgC5QgDKbATgJYA7AOYgAvmMINI5dmEpMxQA

Just choose your value, PT10M requires a knob, part number 5116. You will have to bend the middle pin a bit but it should fit.

 

[ChanceKJ]

hmmm, if I can find the H05 variant I shouldn't need to tho. Kinda just depends on what Mouser/digikey stock. Would like to avoid having to make a special order.

 

[ChanceKJ]

Ok, for the PT10 series...

For the neck board:
PT10-LH05-501A2020 is the 500 Ohm (need 2)
PT10-LH05-103A2020 is the 10K Ohm (need 3)

For the remote board:
PT10-LH05-503A2020 is the 50K Ohm (need 2)
PT10-LH05-103A2020 is the 10k Ohm (need 1)
PT10-LH05-204A2020 is the 200K Ohm (need 2)

 

[ChanceKJ]

ACTUALLY....

Ok, for the PT10 series if you want knobs as well, you need the W series.

For the neck board:
PT10-WH05-501A2020 is the 500 Ohm (need 2)
PT10-WH05-103A2020 is the 10K Ohm (need 3)

For the remote board:
PT10-WH05-503A2020 is the 50K Ohm (need 2)
PT10-WH05-103A2020 is the 10k Ohm (need 1)
PT10-WH05-204A2020 is the 200K Ohm (need 2)


Or the Hex rotors "M" or "G" and the associated shaft, knob, or thumbwheel.

https://www.piher.net/wp-content/uploads/PIHER_PT-10_PTC-10.pdf

 

[ChanceKJ]

Looks like nothing for the H05 variant on either Mouser or Digikey. Octopart lists versions with the H05 mounting pins in a few smaller shops, but it's gonna cost me just as much to ship from them when I'm already making another order from Mouser. Not ideal. Unless another brand makes something similar to the PT10's that I'm just not seeing.

 

[SNESNESCUBE64]

You should just be able to bend the leads on an H01 variant. That's what I've done in the past. I tried to find H05 variant a while ago but had no luck.

 

[ChanceKJ]

Awesome, Thank you I'll grab a few