Phoenix Small Monitor

wmacmonagle

Active member

Donor 2012
Joined
Jul 6, 2010
Messages
2,059
Reaction score
10
Location
Rosamond, California
I had tried to make this to be centered but could not do any shit.

there is total of 11 pot where i can see clearly..

first 3 silver pot seems related to color adjustment.

then 4 of em seem are adjustable to the video itself .

then 3 of em are colored again.

then other 2.. one is seem bright pot.. then focus pot.

I had reached to best posstible but still vertically off!. I had found where i could adjust horizonal to make it fit screen but there is no way for me to move vertical more down..

this problem is similiar with my other black and white montior (pong cocktail).

Phoenixmonitor.jpg


Hope anyone knows better than I do! =)

Thanks in advance
 
It's toei hitach. Type number
370ecb22

Serial. Mom268513

Can u please
Show me where to adjust tube yolk whatever I'm going to upload picture
 
U can see the 5 colored wires i had attached to 60 in 1 Board..

I was not sure where to target. If you could.. copy picture and arrow whre I could adjust and please warn if I NEED TO DISCHARGE to adjust or power off the MONITOR BEFORE ADJUSTING???

this is my first time.. so if this need to be discharged.. i would back off and wait til i get the clamp then POOF up to heaven! =)
 
I've seen this same issue with three different monitor types, all using the multi-cade board. It's possible this is being caused by the board. Do you have another game PCB you can try?
 
thanks for responding.. im all sitting here wanting it to work! =)

i hooked up 60 in 1 jamma and it showing like that under test mode.. i switched to normal mode and it took longer to load the front menu than expect .. it shows yellow blinks on

led 2... then i waited awhile .. it finally changed to green and game mode loads up but showing same position as test mode..

i decided to swap to sf2 that s only jamma board i have now.. and it doesnt show anything..


i decided to remove everything. It shows rainbow (RGB) colored in full screen..

Only thing i had noticed out of all is.. The neck adjustable thing.. i noticed it s not perfectly straight.. i can see the neck to yoke.. is little bend.. maybe few degree off.

does it affect?? should i try to make it perfectly straight and i researched about the yoke.. it required me to discharge several times before fucking around with yoke, neck whatever?? advise?
 
No, I don't think you can do anything with the yoke but screw it up.

Your SF2 might not have booted up if the power to the harness does not include -5vdc, since the multicade pcb doesn't need it...
 
Wish I could be like .. Matrix and upload the Arcade trouble shoot kit in my brain at once! lol
Im gonna sit on it for tonight and try again tomorrow..... Any suggestion overnight would be helpful..

My questinos..

This had possible caused by...

1. Mis wired?

2.. Neck align off?

3. ???

BTW.. Thanks in advance!!!!
 
3: PCB incompatible with monitor

Your Toei only has one way to wire it up, but I'm not sure how it differentiates between positive and negative sync. If it's self sensing and correcting, then it's possible there is an error somewhere. Or there may be a jumper setting somewhere.

But I think it's a PCB compatibility issue, as we've now had three different monitor types all have the same issue with the same PCB....
 
I had connected: to Monitor video board:

Jamma PS: 12,13,14 and SS:12,13

PS
12: Video R (Red Wire)
13: Video B (Blue Wire)
14: GND (Black Wire)

SS
12: Video G (Green Wire)
13: Video Sync (White)

I did not use anything else but

PS/SS
1: GND to Power Supply "GND"
3: +5V to Power SUpply "+5V"
6: +12V to Power Supply "+12V"

That s it.. Just to test everything to see if works.. Im using ICADE JAMMA
 
Just curious, but is the yoke seated all the way up against those rubber wedges ?
 

Attachments

  • hitachioverlook.jpg
    hitachioverlook.jpg
    50.3 KB · Views: 6
Checking.. Can i just push it back in if it s not all the way with out discharging first?

My questions to gain my knowledge.. i had researched and rather to ask here first..

IF I WANT TO WORK From NECK BOARD TO YOLK .. I STILL HAVE TO DISCHARGE?
 
Back
Top Bottom