Leg leveler where to find?

gatordad

Well-known member
Joined
Aug 29, 2007
Messages
1,853
Reaction score
79
Location
Illinois
Looking for a set of 4
NOT the standard 3/8", 16 thread
but the smaller diameter and thread found on specifically a Defender upright.
All I have found online is the standard 3/8, 16 size in different legnths.
Can anyone point me in the right direction.
Thanks
 
Looking for a set of 4
NOT the standard 3/8", 16 thread
but the smaller diameter and thread found on specifically a Defender upright.
All I have found online is the standard 3/8, 16 size in different legnths.
Can anyone point me in the right direction.
Thanks

I'm not aware Defender used anything different other than standard 3/8"... are you certain your Defender is factory?
 
I'm not aware Defender used anything different other than standard 3/8"... are you certain your Defender is factory?
I don't know for sure?
It looks factory....
I'll snap a pic tonight a post it to show what I'm talking about.
 
I replaced my Defender leg levellers with some of those fancy EZ glides from Marco specialities, and they're just the standard size. The only problem is they're longer than original Defender levellers, so my cab sits an inch or more higher than I like it. Might have to see if I can take a hacksaw to them. The other problem I found was that on my Robotron, the mounting hole is at an angle, and because these don't tilt like the originals, it's not sitting flat. But that's a fix-up job for the mounting block, I guess.

In other words, my Defender upright uses the standard 3/8" thread.

These are the ones I bought:

http://www.marcospecialties.com/itemdesc.asp?ic=LL25-EZG

Dominic
 
Last edited:
I replaced my Defender leg levellers with some of those fancy EZ glides from Marco specialities, and they're just the standard size. The only problem is they're longer than original Defender levellers, so my cab sits an inch or more higher than I like it. Might have to see if I can take a hacksaw to them. The other problem I found was that on my Robotron, the mounting hole is at an angle, and because these don't tilt like the originals, it's not sitting flat. But that's a fix-up job for the mounting block, I guess.

In other words, my Defender upright uses the standard 3/8" thread.

These are the ones I bought:

http://www.marcospecialties.com/item...sp?ic=LL25-EZG

Dominic

Bad link for me. :(
 
You can get a 4-pack from Pinball Life for $5.

Or - just order some stuff from Bob Roberts of a certain value, then specifically request them as your lagniappe and you'll get them for free...
 
I know they aren't original, but they are levelers, I like to get ones that don't kill my floors and allow me to move machines. I'll actually get some larger threads and big pads for big machines that I rehab, I know, I know but it's just the leg levelers. Anyways here check it out, anything and everything, not the cheapest, but it's all there....
http://www.mcmaster.com/#catalog/115/1348

When i get really fancy I like using the stainless bolts from here too...
 
I went to a local parts store for refrigerator and washing machine parts - the kind of place the appliance techs shop at. I figured they used these things to balance washing machines and refrigerators. I took one along, and they matched up the thread size with some leveler feet that had nylon bottoms. They're perfect for tile or wood floors, because they can slide without scratching the floor...
 
Looking for a set of 4
NOT the standard 3/8", 16 thread
but the smaller diameter and thread found on specifically a Defender upright.
All I have found online is the standard 3/8, 16 size in different legnths.
Can anyone point me in the right direction.
Thanks

Not sure if I can help you there but I got some from Todd at TNT that are really good on carpet. Moves with little effort.
 
You can get a 4-pack from Pinball Life for $5.

Or - just order some stuff from Bob Roberts of a certain value, then specifically request them as your lagniappe and you'll get them for free...

Did you happen to use these to replace the levelers on your Kangaroo machine? I need to replace mine and wondering if they'd work for Kangaroo.
 
Back
Top Bottom