zork40
Active member
Here is the story on this one....
I have an upright Popeye for sale. I actually own 2 Popeyes. One is in the garage (the one for sale), and the other is in the house. I had intended on turning the one in the garage into a DK, but at this point I need some money and the space couldn't hurt. So, the new plan is to sell the one in the garage, and turn the one in the house into a DK. Here are pictures of the one I'm selling:
http://www.flickr.com/photos/17948214@N00/sets/72157601719924900/with/1258029947/
Be careful not to wander into my other sets, as I have another Flickr set of photos of the one that is not for sale. If you are interested, please look over those pics carefully. There is a small
Now, the one that is for sale has a pretty craptacular bezel and marquee. The one in the house has a NOS marquee, and the bezel and CPO look awesome (I Novus'ed the hell out of it). So, the plan here is to include the good marquee, bezel, and CPO with this sale.
I also have new repro silkscreened sideart for this, included in the sale.
Finally, the PCB. I pulled the PCB out of the one in the garage and sold it as I didn't need it. When I pulled it, it was working. So, if someone is interested in making me an offer on this, I will put the good parts back in place, and test it again to make sure its working OK. I don't remember how the monitor looked, but I know it was working.
The pictures at the URL above were taken awhile ago. I haven't worked on the game since, but I did stupidly cut a piece of the t-molding off to help Bill (audiomidiman) try to repro the offset t-molding. I had planned on completely restoring this cabinet, so at the time I didn't care about the t-molding. So, here is where you can see the missing piece of t-molding:

There is a chunk of the cabinet missing below the control panel on the left side. It is present in the other pictures, but here is a better picture showing it:

The t-molding is also missing from the control panel, but I believe that is just standard non offset:

So, to recap, I am selling:
1. The Popeye cabinet shown here:
http://www.flickr.com/photos/17948214@N00/sets/72157601719924900/with/1258029947/
(there are some pics of DK art, that is not for sale)
2. Along with that, it will have a perfect marquee, and just about perfect bezel and CPO
3. Working PCB
4. New sideart
I'm not sure if I'm going to get any interest in this, so I'm going to hold off on swapping all the parts and firing it up until someone makes an offer. If someone is interested in this, please make me an offer.
Also, I am not dead set against selling the parts but I'd prefer to sell them all together if possible. So, if someone is interested in the PCB, sideart, bezel, marquee, and control panel overlay, let me know.
I have an upright Popeye for sale. I actually own 2 Popeyes. One is in the garage (the one for sale), and the other is in the house. I had intended on turning the one in the garage into a DK, but at this point I need some money and the space couldn't hurt. So, the new plan is to sell the one in the garage, and turn the one in the house into a DK. Here are pictures of the one I'm selling:
http://www.flickr.com/photos/17948214@N00/sets/72157601719924900/with/1258029947/
Be careful not to wander into my other sets, as I have another Flickr set of photos of the one that is not for sale. If you are interested, please look over those pics carefully. There is a small
Now, the one that is for sale has a pretty craptacular bezel and marquee. The one in the house has a NOS marquee, and the bezel and CPO look awesome (I Novus'ed the hell out of it). So, the plan here is to include the good marquee, bezel, and CPO with this sale.
I also have new repro silkscreened sideart for this, included in the sale.
Finally, the PCB. I pulled the PCB out of the one in the garage and sold it as I didn't need it. When I pulled it, it was working. So, if someone is interested in making me an offer on this, I will put the good parts back in place, and test it again to make sure its working OK. I don't remember how the monitor looked, but I know it was working.
The pictures at the URL above were taken awhile ago. I haven't worked on the game since, but I did stupidly cut a piece of the t-molding off to help Bill (audiomidiman) try to repro the offset t-molding. I had planned on completely restoring this cabinet, so at the time I didn't care about the t-molding. So, here is where you can see the missing piece of t-molding:

There is a chunk of the cabinet missing below the control panel on the left side. It is present in the other pictures, but here is a better picture showing it:

The t-molding is also missing from the control panel, but I believe that is just standard non offset:

So, to recap, I am selling:
1. The Popeye cabinet shown here:
http://www.flickr.com/photos/17948214@N00/sets/72157601719924900/with/1258029947/
(there are some pics of DK art, that is not for sale)
2. Along with that, it will have a perfect marquee, and just about perfect bezel and CPO
3. Working PCB
4. New sideart
I'm not sure if I'm going to get any interest in this, so I'm going to hold off on swapping all the parts and firing it up until someone makes an offer. If someone is interested in this, please make me an offer.
Also, I am not dead set against selling the parts but I'd prefer to sell them all together if possible. So, if someone is interested in the PCB, sideart, bezel, marquee, and control panel overlay, let me know.


