FS Multi Vector Control Panels!

Takeman

Well-known member
Joined
Nov 7, 2005
Messages
6,066
Reaction score
1,194
Location
Illinois
Rating - 100%
231   0   0
I have been asked to to make a run of control panels for the Multi Vector (MV) control panel overlay produced by Shilmover. The panel will be laid out to work with his overlay and mount in a Space Duel Cabinet.

See pics and the thread here. http://forums.arcade-museum.com/showthread.php?t=178103

My panels will be offered 2 ways. 1: punched out as you see his panel is, with the addition of stud mounting for the sticks and spinner, hinge, lock down tabs, powder coated smooth black & die punched holes. There is one tiny catch. Do to the forward location of the spinner, I had to place 2 additional mounting holes in the hinge (not seen when installed) on either side of the factory center hole. The end holes are in the factory locations. You would have to drill 2 holes in your cab to fasten the center of the panel to the cab. I dont think most people would care, but I wanted you to make an informed purchase.

Panel 2: Would be considered a "blank", meaning no holes punched with the exception of the hinge, which is the same on both panels. Blank panel has lockdown tabs, hinge & smooth black powder coat.

Now for the details. Due to the great cost involved, I will have to do a presale order on this. Panels are prices as follows:

#1 Punched MV panel is $80 plus $20 shipping to USA 48 which includes a custom box

#2 Blank panel is $70 plus $20 shipping to USA 48 which includes a custom box

Paypal payments to [email protected] Be sure you put your KLOV name in the comments and what payment is for.

I'd like to get 20 presold to make this work right. From the time I say go, expect 3-4 weeks. I am only going to run what I have sold, so there will likely be no extras. I will update on a regular basis.

I'll give the pre-order until May 23rd @6pm Central time. If the minimum is met before hand, I will start the run early. After the 23rd, the panel will go up. I am on a bit of a time crunch on this as Shilmover needs his panel back for a prior commitment.

Overlay is not included.

If for some reason the minimum is not met, I'll refund all monies.

I'll keep a master list here for you all to see.

Any questions? Shoot me a PM.

Paid List:
Shilmover - 1 punched - SHIPPED
Mailce95 - 1 punched - SHIPPED
Alexred - 1 punched - SHIPPED
James_in_MD - 1 punched - SHIPPED
CSbartz - 1 punched - SHIPPED
Scon_fu - 1 punched - SHIPPED
Djw90 - 1 punched - SHIPPED
Dezbaz - 1 punched - SHIPPED
Bheineck - 4 punched / 2 blank - SHIPPED
Cnlmoore - 1 punched - SHIPPED
Komodo - 2 punched - SHIPPED
Retroactive - 1 punched - SHIPPED
Veeb0rg - blank - SHIPPED
DanP - 1 punched - SHIPPED
SRW - 1 punched - SHIPPED
Wolfeel - 1 punched - SHIPPED
Bryan95502 - 1 punched - SHIPPED
Eclipseeye - 1 punched / 1 blank - SHIPPED
GackAttack - 1 punched - SHIPPED
Tooz - 1 punched - SHIPPED
Dj dns - 1 punched - SHIPPED
Silverunicorn - 1 punched- SHIPPED
Oppolo - 1 punched - SHIPPED
Retroshaun - 1 punched - SHIPPED
Hereitcomes - 1 punched - SHIPPED
Alejandromad - 1 punched - SHIPPED
Tanio - 1 punched - SHIPPED
Bigarn - 1 punched & 1 blank - SHIPPED
CocktailDave - 1 punched - SHIPPED
Gatordad - 1 punched - PICKED UP
Jimk - 2 punched - SHIPPED
Cloggans - 1 punched - SHIPPED
Hisnice - 1 punched - Ready for Pick Up
wmacmonagle - 1 punched - SHIPPED
Robotron Jon - 1 punched - SHIPPED
Johnvv - 1 punched - SHIPPED
Khabbi - 1 punched - SHIPPED
Joeycuda - 1 punched - SHIPPED
Arcaderob - 1 punched / 1 blank - SHIPPED
Dclem - 1 punched - SHIPPED
Louisurfer - 1 punched - SHIPPED
mxracer47 - 1 punched - Ready for Pick Up
Nomore25s - 1 punched - SHIPPED
Xtrasmiley - 1 punched - SHIPPED
Aesop - 1 punched - SHIPPED

---------
48 - punched / 6 - blank

---------
54
 
Last edited:
I know a cracker in Ohio that makes new cabs!

I'd love to buy one of his but he's to far for me to drive. If someone from the
North east coast went out to Bretts they could probably make money on the trip.. they'd be bringing back a bunch of cabs.. I know 3 guys that want cabs and there are probably more guys.
 
What the heck happened to not in a hurry?!! :)

I'd love to buy one of his but he's to far for me to drive. If someone from the
North east coast went out to Bretts they could probably make money on the trip.. they'd be bringing back a bunch of cabs.. I know 3 guys that want cabs and there are probably more guys.
 
I have an Oscar Vortex spinner and a pair of compact topfire sticks. Will these work with the punched panel?

Ooooh, good question. The studs for the sticks /spacing are for a wico base. That is VERY common with other sticks as well. Im not familiar with your specific sticks tho. Grab a Wico base and compare. If memory serves, the spinner used was an Oscar, but I have to double check that. I'll ask Shillmover too...
 
Last edited:
If it looks like this will happen for sure im in!!:)

If everyone follows through that posted on the interest thread, this will happen. Time crunch is that I need pre paid commitments with in the next 2 weeks to make it happen.

Shilmover has promised his panel/game to arcade/pinball party at the end of May. I need his panel for the drawings and comparison to the repro for accuracy.
 
Payment sent.

Is someone going to make a run of the Multivector control panel overlay, preferably a silkscreened version?

Chris

I think Shilmover was working on that. I have seen his overlay in person and it looks really nice. Not sure where he had it printed, but it looks VERY good and it's stuck to the panel well.
Might not need to go with an expensive screened cpo. Just my opinion.
 
A few things...

- I need this panel back for the NW Pinball show as its commited to be at the show. So if you want this to happen, get one ordered...
- Once I get the new panel, i will tweak the artwork so that it matches that one exactly. Not sure its worth having the art silk screened. As Takeman stated, the CP looks really, really nice as is. I will either have them printed or just get the files to the person who printed this one for me and have you all ping him. :)
- spiner was the Oscar repro spinner, but i believe the Tempest spinner is identical.
 
If it looks like this will happen for sure im in!!:)

Dan,

This will happen if enough people pre-pay. Takeman is legit... if this does not happen he will refund the $.

I would hate it for 15 orders to come in because 10 people are waiting for it to happen and then it does not happen...
 
A few things...

- I need this panel back for the NW Pinball show as its commited to be at the show. So if you want this to happen, get one ordered...

Message sent re shipping to Aust.

Anyone got info on where to get a spinner & harness from?

Cheers
 
Message sent re shipping to Aust.

Anyone got info on where to get a spinner & harness from?

Cheers

I ordered mine from ebay... looking for the seller as he had a few. I believe a tempest spinner will work too (checking on measurements).

There is no harness, you will need to make your own attached to an ipac or something similar...

If you are using DOS, you will need an older DOS based OptiPac
 
If everyone follows through that posted on the interest thread, this will happen. Time crunch is that I need pre paid commitments with in the next 2 weeks to make it happen.

Shilmover has promised his panel/game to arcade/pinball party at the end of May. I need his panel for the drawings and comparison to the repro for accuracy.


Paypal Sent for Punched MV panel :cool:

Dan,

This will happen if enough people pre-pay. Takeman is legit... if this does not happen he will refund the $.

I would hate it for 15 orders to come in because 10 people are waiting for it to happen and then it does not happen...

I agree:)
 
Back
Top Bottom