FS: Amplifone 19" tube with yoke

m_mcgovern

Active member
Joined
Sep 10, 2007
Messages
1,318
Reaction score
7
Location
Evesham, New Jersey
Rating - 100%
13   0   0
OK, WG6100 owners...here is your chance to upgrade! I have a 19" Amplifone tube with yoke, convergence rings, degauss coil for sale. Monitor is nice and bright. Does have very light burn near the top and a 1/8" X 1/4" burn spot in the center. The light burn is not noticeable behind tinted glass. The burn spot is only noticeable during Death Star explosion.

After toying with the idea of using this in my SW cockpit restoration, I have decided to go for broke and build a 25" setup instead. So, I am selling this to defray some of the cost. This tube does not come with HV or deflection pcbs as I need them for the 25" set-up. I will also throw in several official Red HV flybacks. More than likely dead, but you never know...

Here are pics of the tube with a close up of the burn spot (if you look towards the top you can barely see the faint burn-in on the 2nd pic)
4017503353_4312e1ae1a.jpg
4017503361_53562975ed.jpg


Here are pics of the tube with and without the tinted glass displaying graphics:
4018285342_9fb8863b55.jpg
4017503373_5458346cb9.jpg


Finally a picture of the back:
4017503377_36f5b55303.jpg


Asking $135. Local sales preferred as I would rather not ship it.
 
I will give you $135 for everything except the CRT. You can sell that bare later if you accept.

The catch is I am in Australia, so I need freight to postcode 6066, if possible

Yes?
 
I'd need it shipped, but will buy it. My 6100 tube in my Star wars has a huge burn hole in the tube, and I'd rather have a Amplifone with a higher refresh rate anyways. Sending PM.

Edit: And if this goes through does anyone have any of the other boards I will need?
 
Last edited:
I'd need it shipped, but will buy it. My 6100 tube in my Star wars has a huge burn hole in the tube, and I'd rather have a Amplifone with a higher refresh rate anyways. Sending PM.

Edit: And if this goes through does anyone have any of the other boards I will need?

Well hopefully he is keen on my offer mate, but we will see :)
 
I'd need it shipped, but will buy it. My 6100 tube in my Star wars has a huge burn hole in the tube, and I'd rather have a Amplifone with a higher refresh rate anyways. Sending PM.

Edit: And if this goes through does anyone have any of the other boards I will need?

Quarter arcade have a few deflection boards :)
 
Amp Tube, 25" parts

PM Sent; If the tube is still available drop me a line. I can use a 19" and I have some parts that can be used for the 25". NJ local.

-Dan
 
If OP has sold his stuff, I have 2 tubes FS. No yoke, rings, mounting plates, etc. Just the tube. 19" versions. I can ship.
 
OK, WG6100 owners...here is your chance to upgrade! I have a 19" Amplifone tube with yoke, convergence rings, degauss coil for sale. Monitor is nice and bright. Does have very light burn near the top and a 1/8" X 1/4" burn spot in the center. The light burn is not noticeable behind tinted glass. The burn spot is only noticeable during Death Star explosion.

After toying with the idea of using this in my SW cockpit restoration, I have decided to go for broke and build a 25" setup instead. So, I am selling this to defray some of the cost. This tube does not come with HV or deflection pcbs as I need them for the 25" set-up. I will also throw in several official Red HV flybacks. More than likely dead, but you never know...

Here are pics of the tube with a close up of the burn spot (if you look towards the top you can barely see the faint burn-in on the 2nd pic)

Here are pics of the tube with and without the tinted glass displaying graphics:




Asking $135. Local sales preferred as I would rather not ship it.

Hi there buddy, did you sell it to someone?

:D:D:D:):)
 
Based on his reply to me he is waiting a few days to make sure there is no local buyer. Should that fall through I think you are first in line for all but the tube.

I could be wrong though, just trying to satisfy your curiosity. :D
 
Back
Top Bottom