PhoenixStar
Well-known member
S.T.U.N. Runner seat and dash bezel. Star Rider space cycle.
Custom Vac forming available
- Thread starter phineas foo
- Start date
phineas foo
Permanently Banned
OK I have rtead over the items people have asked for since last week.
Te bowling pins are injection molded, not formed. I cannot do these in that mnedium. I can do cast parts of them and I can tell you how. PM me.
The seats would be good but more than likely wont fit on my table. I would need measurements to make sure.
The bezel shrouds are always a good thing and most will fit my table. Get me measurements and PM me with the size. I am already doing some of those for another member, different games.. so it is possible.
and BTW, YES.. I can get duramold cabinets done. BUT.. I need a cabinet to take molds from. But yes folks, they can be done.
M
Te bowling pins are injection molded, not formed. I cannot do these in that mnedium. I can do cast parts of them and I can tell you how. PM me.
The seats would be good but more than likely wont fit on my table. I would need measurements to make sure.
The bezel shrouds are always a good thing and most will fit my table. Get me measurements and PM me with the size. I am already doing some of those for another member, different games.. so it is possible.
and BTW, YES.. I can get duramold cabinets done. BUT.. I need a cabinet to take molds from. But yes folks, they can be done.
M
tridentsx
Member
phineas foo
Permanently Banned
So far only one person has come forward and sent me parts to have work done. I will not steal their thunder at all. So when they are ready to let you know, it will be done.
So many good ideas, but no one is coming forward to get anything done other than the asking stage.
Brick Top
Well-known member
Hey Phineas, I have a PP shroud you can take a mold from.
It has ciggy burns on the dashboard, so you all can get the exact same burns I have, wouldn't that be cool?
It has ciggy burns on the dashboard, so you all can get the exact same burns I have, wouldn't that be cool?
Hey now, there are 2 R's in Hillsburrito! Hopefully toward the end of this month. I'm hoping to get the pin working this weekend and I have some monitor work I really want to get done before having a party. But you know you're always welcome to stop by if you're in the area. Don't need a party to play some Sea Wolf!
Phin, on the Spy Hunter seat, it's only the seat back that's plastic. So hopefully it wouldn't be too big. I can get some measurements on it if you want. I got a PM expressing interest in it. If this is something you can make, I will see how much interest I can drum up, but I bet we could get enough. I think it's common for these to be cracked.
Phin, on the Spy Hunter seat, it's only the seat back that's plastic. So hopefully it wouldn't be too big. I can get some measurements on it if you want. I got a PM expressing interest in it. If this is something you can make, I will see how much interest I can drum up, but I bet we could get enough. I think it's common for these to be cracked.
phineas foo
Permanently Banned
Shan- Gotcha! I have a table right now that is 16 x 20 working area... but i am making a new one that is 22 x 22 working area. So yeah, if it fits, I can do it! Yes, The Burrito! LOL!
Let me know the size.. I am off of Golden and 52nd ave...
M
Let me know the size.. I am off of Golden and 52nd ave...
M
tridentsx
Member
The problem is that original exterior has leathery texture to it, like grains, don't know how to explain it. English is not my native language. The inside is smooth. If the texture isn't reproduced I might as well use sand paper, bondo and spray paint.
I am not sure how the original part was made.
Last edited:
tridentsx
Member
I measured the pole position shroud, its roughly 24" x 24", is that to large ? If not I will remove the best out of the three I have and ship it to you this weekend.
Sega Out Run plastics
My friend and I are working on his Sega Out Run upright and he *DEFINITELY* wants repros made of all the plastics that are on the upright.
Put us down for a set of those if you can get enough market to do some Sega Out Run plastics.
My friend and I are working on his Sega Out Run upright and he *DEFINITELY* wants repros made of all the plastics that are on the upright.
Put us down for a set of those if you can get enough market to do some Sega Out Run plastics.
Mindl3ss
Well-known member
Shameless plug, I know... but I have one for sale right now. If it's needed as an original, PM me. I'm in Washington, along I-5, which I'm pretty sure I've read somewhere that the OP is around Portland.
shirkle
Active member
I think pinball ramps would be into this. I wouldn't mind having an extra ramp for my Swords of Fury. I bet there are other popular ones that had a tendency to crack. You might want to mention this service in the google pinball group.
jcterzin
New member
Id buy a set too for outrun.
Daviea
Permanently Banned - See: Ram Controls Forum Secti
I just wanted to put my two cents into this thread.
Phineas Foo is legit guys. He's done some initial work for me and it's quality stuff!! Being a stickler for the details (a little OCD, some of you have called me), I know when I'm working with someone who knows what they're doing. Phineas knows what he's doing and he's easy to deal with. If you were on the fence before, get off that fence and send him some of your business! And if I were you, I'd do it NOW, before he smartens up and leaves us for something better!!
So, Phineas gets two thumbs way, WAY up as far as I'm concerned.
Just remember, the part needs to be smaller than 24" x 24" (correct me if I'm wrong, Phineas), so keep your parts requests relatively SMALL. If you have an original part in hand, PM him, get his info and send your original to have remade. It's pretty simple and painless.
Thanks for being part of our community, Phineas!!
Phineas Foo is legit guys. He's done some initial work for me and it's quality stuff!! Being a stickler for the details (a little OCD, some of you have called me), I know when I'm working with someone who knows what they're doing. Phineas knows what he's doing and he's easy to deal with. If you were on the fence before, get off that fence and send him some of your business! And if I were you, I'd do it NOW, before he smartens up and leaves us for something better!!
So, Phineas gets two thumbs way, WAY up as far as I'm concerned.
Just remember, the part needs to be smaller than 24" x 24" (correct me if I'm wrong, Phineas), so keep your parts requests relatively SMALL. If you have an original part in hand, PM him, get his info and send your original to have remade. It's pretty simple and painless.
Thanks for being part of our community, Phineas!!
