BurgerTime Restoration

arcadefr34k

Active member
Joined
Sep 5, 2011
Messages
1,275
Reaction score
21
Location
Victoria, Texas
BurgerTime was a game I had been looking for years for. I finally found one (thanks 1iblind!) and decided to restore it. So, here it goes:
Still needs to be purchased / found:
-Bezel bracket
-Top marquee bracket
-Kickplate artwork
-Coin box bracket

**NOTE** Some pictures are not in order
01/04/13 - BurgerTime arrives.
2566vwo.jpg

33w2s10.jpg

ets753.jpg

yfjq1.jpg

kbx1sn.jpg

25a0n44.jpg
 
Last edited:
01/06/13 - Bondo work on the front, sides, and back.
2wpnj1w.jpg

2i6z8ky.jpg


01/09/13 - Reproduction side art arrives from gameongrafix.com.
b88p51.jpg
 
01/21/13 - Control Panel Overlay applied. If you're wondering, I did not apply it wrong. I was informed by the seller that the holes were cut wrong.
9s6zgi.jpg

rcvudu.jpg
 
Last edited:
Nice job! Were you going with the vinyl sideart from the get-go, or did you consider going with stencils at first and decide against it?
 
It appears that the vinyl sideart has been printed the wrong size.... Are they aware of that?

I realized it before applying it but went with it anyways. I haven't contacted gameongrafix yet but I was going to today. I think it's the right size but the hat is too small.

Nice job! Were you going with the vinyl sideart from the get-go, or did you consider going with stencils at first and decide against it?

I planned to go with vinyl from the beginning. I don't trust myself or anyone I know to stencil it lol

Also, these items arrived today from Twisted Quarter.

-Kickplate
-Marquee light
-T-molding
-Coin box
-Coin door bulbs & bulb sockets
-Rubber leg levelers
-New replacement wheels
 
Last edited:
01/21/13 - Control Panel Overlay applied. If you're wondering, I did not apply it wrong. I was informed by the seller that the holes were cut wrong.

That's the backtothearcade CPO? That's disappointing that the holes are off by so much.
 
That's the backtothearcade CPO? That's disappointing that the holes are off by so much.

Yep, thats the backtothearcade CPO. And yeah, I it sucks but I was just happy to find a good CPO.

Also, more pictures and updates will be posted tonight.
 
01/24/13 - Put on new T-Molding. The lighting makes the T-Molding look faded. I also installed the light fixture for the marquee but I gotta measure the voltage coming from the outlet on the power supply to make sure it is 120v and not 100v. I was going to add new leg levelers but they are too big. They came with a new mounting plate but I gotta put them on this weekend. The wheels use a bigger mounting frame so I have to put them on before I put the new leg leveler mounting plates on. So, this weekend that will be done.

2iuw1ld.jpg

2buqgy.jpg

2m6aiap.jpg
 
Last edited:
01/24/13 - Put on new T-Molding. The lighting makes the T-Molding look faded. I also installed the light fixture for the marquee but I gotta measure the voltage coming from the outlet on the power supply to make sure it is 120v and not 100v. I was going to add new leg levelers but they are too big. They came with a new mounting plate but I gotta put them on this weekend. The wheels use a bigger mounting frame so I have to put them on before I put the new leg leveler mounting plates on. So, this weekend that will be done.

2iuw1ld.jpg

2buqgy.jpg

2m6aiap.jpg

Cool Poster.....:cool:
 
01/28/13 - Installed wheels on BurgerTime. Decided to ditch the leg leveler plan due to my small room and having to move games a lot.
 
That's the backtothearcade CPO? That's disappointing that the holes are off by so much.

Yep, thats the backtothearcade CPO. And yeah, I it sucks but I was just happy to find a good CPO.

Wow, that is not good to hear. I have one I haven't unwrapped yet as my restore is behind a few other cabs.
 
02/07/13 - Decided to go the 60 in 1 route with this machine. Don't worry, all parts will be stored on a shelf in an air conditioned room :) - Anyways, wired the new power supply, the 60 in 1 PCB, the marquee light, and the coin door lights. Tomorrow I will be swapping the k4600 out of my Galaga and into this machine.

6ibo5u.jpg
 
Back
Top Bottom