-
Please post all monitor technical topics in the Technical - Videogames - Monitors section, not in the General Help section.
Berzerk coin door info
- Thread starter jammatt
- Start date
Here's mine! Its mid-restoration. So, some of the wires are not repaired. I have not gone thru the coin door yet. Let me know if you need more. Good Luck!
Attachments
Thanks a lot, your pictures will help me a lot.
That 2 wires without pins goes to connector?
On the manual cant find nothing about.
If you can just take a picture on the other side of the connector, where the wire enters.
Also do you have the female connector also?
I thing they go to RCR-1000 pcb? I need that to
Thanks a lot
Matt
That 2 wires without pins goes to connector?
On the manual cant find nothing about.
If you can just take a picture on the other side of the connector, where the wire enters.
Also do you have the female connector also?
I thing they go to RCR-1000 pcb? I need that to
Thanks a lot
Matt
Those wires were cut before I got the game. They did originally go to the the 9 pin "molex" type connector (male pin, female plug) used for the coin door harness. You can see where they were cut in the attached pictures.
OK. Here is a picture of the back of the connector. Also, I have noted the wire color and assignment on the coin door. Unfortunately, two of my wires are cut at the door and I haven't had been able to figure out where they go yet.
https://drive.google.com/file/d/19KkGOIo_O5sMfrHf-j6CXZgEpuP4ckKr/view?usp=sharing
Also do you have the female connector also?
I thing they go to RCR-1000 pcb? I need that to
I do not have the other part of the harness. It was missing when I bought the game! But yeah, all these wires go back to the RCR-1000 board:
https://drive.google.com/file/d/1oqC-iEXTSYRRR0ydUfAHflMszAShPYv2/view?usp=sharing
Berzerk is a great game game. Good luck!
Attachments
Last edited:
Congrats on finishing your repairs.
Mine isn't finished yet. Still a few more months to go realistically. I have finished the bezel flaking paint repair and the monitor repairs, and most of the cabinet wiring. I have a repro CP and original batstick. My CP still needs wiring.
I was all gung-ho about getting the old board set working, but have lost some momentum on that. I've got a room full of cranky old games and only so many hours per day to work on this stuff. I'm leaning more toward a JROK board now. I really want to play it.
Mine isn't finished yet. Still a few more months to go realistically. I have finished the bezel flaking paint repair and the monitor repairs, and most of the cabinet wiring. I have a repro CP and original batstick. My CP still needs wiring.
I was all gung-ho about getting the old board set working, but have lost some momentum on that. I've got a room full of cranky old games and only so many hours per day to work on this stuff. I'm leaning more toward a JROK board now. I really want to play it.
Yes i can understand
mine was working with a JROK board but I wanted to bring it back to the original. If you need some pictures just ask me Hello everyone,
Does anyone have the connector number for the coin door harness ? Mine is gone and need to e replace it . Also need to reconstruct the cp harness if anyone has pics an pn# for that connector
Thanks
Bruce
Does anyone have the connector number for the coin door harness ? Mine is gone and need to e replace it . Also need to reconstruct the cp harness if anyone has pics an pn# for that connector
Thanks
Bruce
KenLayton
In Memoriam
Mouser part numbers for the AMP/TE Connectivity Commercial Mate-N-Lok connectors:
571-14802740 Socket Housing, 9 position
571-14802770 Pin Housing, 9 position
571-606201 Crimp pin terminal
571-606191 Crimp socket terminal
571-14802740 Socket Housing, 9 position
571-14802770 Pin Housing, 9 position
571-606201 Crimp pin terminal
571-606191 Crimp socket terminal
Last edited:
