centipede

I have an Atari Centipede machine in excellent condition. Was owned privately for many years and well taken care of. A fellow KLOV member advised me to proactively change the Big Blue even though everything was working totally fine. I went ahead and bought a new Big Blue from Bob Roberts...

For Sale: Centipede Cabaret (Irish Edition) - SOLD Cabinet Condition: Control panel overlay and bezel are original, and in excellent condition Wood grain vinyl is nice overall with a small section (about 2 inches) pealing back along the top right side Original Trackball, may want to rebuild...

Who makes the highest quality Control panel overlays I'm looking for the best Centipede CPO out there.

Hi - I have an Electrohome G07-CBO (CRT TYpe 19VJTP22/19VMAP22) monitor in my upright Centipede game. It had predictably been showing signs of deteriorating with screen sag and I finally lost the picture (this coincided with replacement of the firing button and trackball rollers - seems...

Hi everyone, I am a newly registered member. I recently acquired a very nice Centipede cabaret machine. The machine is complete and working with two exceptions: 1. The coin mechs inside the coin door are gone, and the wiring harness was cut. I'm not concerned with replacing the mech, but I...

Atari Wiring Harnesses (BattleZone, Cloak & Dagger, and Centipede) Time to let go of a few items to fund my Tempest cabaret restorations, so the following Atari wiring harnesses are for sale: - BattleZone (possibly Red Baron - see below) Harness is complete with the power harness, power...

What classic Atari harness had two headers the same size? While digging through my parts this evening, I ran across a few Atari main wiring harnesses I hadn't seen in a while. The first is a Cloak and Dagger, while the second is Centipede. However, the third is not labeled and I am having...

I purchased an original Centipede Arcade game on a whim today froman antique shop to complete my Game Room. The guy I bought it from said he put in a new card after the original died, it played one game then died again. Now, I know nothing about restoration but I knew I wanted it. He offered it...

Hi, About to clean my G07, and there is a rusty metal casing mounted on the back of the monitor. Can I leave it off if I just reinstall the degauss-ring and small electronics after cleaning? Untitled by barrybuise, on Flickr Untitled by barrybuise, on Flickr

Need the blue cardboard bezel and a marquee for upright model. Ryan

Hi to all! Hope you guys can light me with some information... So I have a upright centipede that was working fine.. as the trackball goes: up, down, left, right (I have already replaced rollers, bearings and the ball itself) but this machine will have a loud hum that could be heard through...

Hello all, Relatively new here. and I'd also say im relatively new to arcade repair. I got this centipede from a guy who said its been sitting in a barn for over 30 years. Everything in it was original - I replaced the PCB, power supply and audio board. I decided to re-cap the G07 myself...

Original, pristine silkscreened glass. No chips, scrapes, scratches or blemishes. $60 shipped, send me a PM if interested :)

I am looking for centipede �� parts . What I need - Back door �� Bezel still looking Marquee original 1 control panel complete or not complete --- found one still need one more 19" monitor ----- found Please pm what you have �&#56347...

I have been finishing my Centipede restore; I put in the WG and hooked everything up and I got the below screens; they didn't move much but they changed a bit each time I powered up. Full disclosure: Back when I was an idiot and knew nothing I had a Taito Big Event golf that I tried to put...

Hello, Let me start by saying I am pretty new to arcade repair, but do have some experience in electronics and circuit theory. I just recently picked up my first full size game, a centipede upright. The game powers on, but plays blind (everything lights and game coins up). My idea was to...

Looking to sell 2 Atari cabaret games - Centipede & Tempest Both games are working 100% Full tread on Tempest located here: http://forums.arcade-museum.com/showthread.php?t=336099 Pickup in North Providence, RI or will work with buyer to ship via NAVL Asking $1250 for the pair...

Got a Centipede I bought from a dirtbag on ebay who represented it as "working last time I looked" (which should have been a red flag). Bold69 and I fired it up with a Jamma Adapter (also for sale) and got some garble. Would like to get $75 shipped and $20 for adapter. MMAO

Looking for an Ice Cold Beer or any Cabaret Games. Located at 26501. Must be working. Thanks!

Two Atari Classics - Centipede & Asteroids for sale MD/VA/DC Atari Centipede Cab is solid with typical knicks and scrapes. Has a Willis CPO that shows wear around the trackball. Glass is in overall nice shape as is the marquee. No hacks. It was not working when I got it but I swapped the...