Search results for query: *

Okay got it all figured out. Turns out that it's working properly, but there's no explanation anywhere about the Left Ramp shot needing to be part of a combo (with Red Arrow lit) in order to have it lock a ball. That would have been great to know. Oh well, I know now. Also, not explained...

I noticed that my DM is not Locking Balls as it's supposed to, but I can't figure out why. The Cryo Claw Lock Freeze DOES work correctly, but the left ramp is not locking them as it should after clearing the standup targets. I can have all 4 Freezes flashing, send a ball up the left ramp 20...

That's the only unfortunate part of the kit, you have to use tape, scotch or clear obviously preferred. My fear was that it would darken the light wire wherever there was tape, but that didn't happen at all. Very tricky and takes a while to do, but looks really cool. Oh, one downside to this...

I got this off of ebay, https://www.ebay.com/itm/DEMOLITION-MAN-Pinball-Light-Wire-Mod-BLUE/222504269375 but was advertised to only cover Wire Ramp #1, #3, and the ACMAG portion of the Double Wire Ramp. However, there was just barely enough light wire to also include Wire Ramp #2, and the...

I just got my Demo Man up and running after weeks of tracking down bad or shorted wires or connectors. I had 3 different situations where I had 2 wires going out the back side of a pin, but only one would check for continuity if tested at back of pin. However, because one wire was checking for...

I went and investigated all 3 flippers. I checked for continuity between the grounds as well as the inputs on the fliptronics board for the switches and also the coils. Everything checked out as it should, as far as I could tell. I then decided to clean up/zip tie some of the wires underneath...

WOOO WHOOOO!!!! Finally, the nightmare is over. Claw and Elevator and all switches except for 1 are back up 100%. It turns out I had 2 more connectors that had issues. Both were 2 receptacle connectors, and both had one wire going into each receptacle on one end, but 2 wires going out the...

Yeah, I went ahead and got them all going again by creating new and longer reaching wires and harnesses for each of them. I got them all working again. The problem now is I still have 3 which used to work fine. The Claw position 1 and 2 are reading open, and also switch #24 which is supposed...

Well, getting somewhere here. It confused me when all of the optos went out at once, when some of them were working fine before. Also, the bottom popper started popping just like the top popper. I already found a bad ground to one opto and one bad signal wire to another, but they all went out...

Found a short in the ground wire going to the Bottom Popper, the only OPTO that was reading as closed originally in the switch test mode. But, after fixing it's short in the ground wire to the Opto sensor itself, now even that Opto is showing as Open in the switch mode test. But, no errors...

I picked up a fully working DM over a month ago. Everything worked perfectly, until I took it completely apart to clean it. Now, I cannot get rid of 3 errors, and a total of 4 problems. I get Right Flipper EOS error, the Claw out of range error, and the right diverter stuck closed error on...

Cool, I'll check them out. Thanks guys!

Just picked up a Demo Man, and it needs a major cleaning. Warning...RANT: I swear it seems sometimes like many pinball owners don't take care of their stuff. Why would anyone keep a pinball in a garage that is always being opened and closed, and used for parking cars? Wife is definitely one...

Ah! That makes sense. I was reading it from the button combination standpoint. Thank you! 1 down, 2 to go.

Found this page, and was wondering if anyone has corrections for the Road Show eggs: http://hem.bredband.net/b257182/Cows&Easter.htm#R Specifically for this section: RS L6: 5R + 1L + 1R + 1L + 5R + 1L, Credits (attract mode) 4R + 1L + 4R + 1L + 19R + 1L, Special Thanks...

Well, got my fuses, did a little more testing, but fuse still blowing when the bulldozer Eddy was hooked up. So, I took a CLOSE look at my re-flowed solder on the Eddy board. Turns out, solder was shorting the power and ground to the eddy (pins 1 and 2) underneath connector housing/plastic on...

Strange that Fuse 115 was left off of chart. But I guess that's because of the always closed "switch 24" (page 39 of the manual at: http://www.pinballsupernova.com/Williams%20Repair%20Guide/Williams%201990-1999%20WPC.pdf). By the way I get the exact message on page 41 about F115, F116, J112...

Will do as soon as fuses arrive. Will report back asap. Thank you!

Never mind, answered my own question. 35 amp 200v

Okay the +12v unregulated goes thru BR5 and C30 (25v 15,000 uf). I don't know anything about the specifics of Bridge Rectifiers, and the manual for Road Show doesn't give any info. on BR5. Can someone school me on which Bridge Rectifier I should buy (if I end up needing one)...