Search results for query: *

Hey guys, getting close to wrapping up my Defender restore. Does anyone know how to wire the service buttons for the coin door? I "think" these buttons are used for multiple Williams games. I can only assume the existing connected wires are correct but I have no idea where these other wires go...

Selling a NFS Underground upright. It's a nice shape, has some scratches on the side art, nice big CRT monitor. Depending on location, I can ship for about $250-$300. Asking $850 Thanks!

Hey, I'm needing the upper bezel bracket for a Defender upright. I may also be interested in the lower marquee bracket just because I'm not sure my cabinet has the correct one. Thanks!

I've been having issues with the audio on my Gorf. I've reflowed the solder on the header pins on the audio board and that seems to have fixed my issues. The volume pots are still a little erratic though. I believe they are 200 ohm pots and they are the same physical size as the pots on the...

I'm really not sure which Midway style bucket it uses but it doesn't appear to be the one I have in my Spy Hunter or Burgertime (metal handle also found in a Ms Pac-Man). Thanks!

Anyone know if the A082-90421-B000 PS will work with Gorf? I think I initially picked this up for my Burger Time machine but ended up not needing it. Thanks!

Does anyone have any pics of the connectors on a Gorf power supply? I'm especially interested in the 12pin connector. Someone soldered wires directly to the pins instead of using a molex connector! I've looked at the manual and this is how I'm reading it...but would like another visual... 1 -...

Looking for a coin bucket for a Defender - thanks!

Is a yoke that works on a WG K4900 compatible with a G07 chassis? I measured the ohms and it seems reasonable (H: 2.2 / V: 56.9).

I'm about to pickup a nice but gutted Defender cab that had been wired JAMMA. I'm looking for the original harness, power transformer, boards, etc. Thanks!

Hey guys, I'm starting to have an issue with my Frogger board. The game boots and plays fine for maybe 20-30 minutes then it throws this error. Any ideas? Thanks!

Does anyone know if the Electrohome G07-CBO H Center & V Center Pot mod will work on the 13" G07-FBO chassis? Below is a link to the mod for reference. I've installed this a few times on a G07-CBO and it worked nicely - thanks...

Hey, I’m looking for a control panel for a Ms Pac-Man cabaret. Condition doesn’t matter, thanks!

I find Defender to be a very difficult game but it's one on my list to get. I did find a cocktail version that looks nice but a friend of mine tells me the cocktail version is harder to play than the upright. Anyone know from experience? Thanks!

I have one DK remix kit and a DK/DKII multi-kit. These work on a DK 2-board stack. They might also work on the 4-board but I've never tried. Asking $50 each or $90 for both (shipped) Thanks!

I've had this board boxed up for awhile, never used and no longer have any use for it. I know I bought it as a working board but I have no way to test it now since I no longer have my Turbo. I'm selling as untested, asking $125 + shipping, thanks!

Hey guys, I'm looking for the following parts for a Pac-Man cabaret. Black plastic monitor shroud that goes over the monitor but rests under the glass bezel Marquee Coin bucket Maybe glass bezel depending on condition Thanks!

Hey guys, I'm working on installing the Taito multifit (EA, JH, JK) on a JH board. My board doesn't look like the board in the instructions on Joe's site. Anybody out there have this kit? I think I can figure most of it out but the instructions refer to removing an MCU chip on the CPU board. I'm...

Hey guys, looking for a working lamp driver board for my upright Spy Hunter. Thanks!

I cannot seem to keep the weapon lights working on my Spy Hunter. I've replaced the resistor at R19 and the cap at C8 on the lamp driver board. Once I did that, the lights started working. After about a day or two they are off again. I appreciate any help, this is driving me nuts. I have two...