Search results for query: *

I can help. I sent you a PM.

Rainbow power cable is not needed when you use the stock DK/DKJ wiring harness -- only required when using the edge connector harness style.

Remove the 10 pin wiring harness from the white header pins and plug it into the P3 location on the other PCB (the video board). You need to supply power to both the CPU board (9 pin connector) and the Video board (10 pin connector).

Pretty certain that the pink/blue revolver style guns required a wiring adapter/extension. I quickly grabbed one and took a photo. See attached photo.

Of course. Shoot me a message. I literally made a set this past week for someone!

There's a specific Nintendo manual out there that outlines that pretty well -- should be easy to find in an online search. Other than PCB and control panel, you will need "half" of a new harness -- the 44 pin edge connector side of the harness from the UniSystem will remain the same, but you...

You can combine the FG roms using 27128 EPROMs and populate them into the 4 FG sockets on the Qbert board, however you still need to cut traces, run wires, and update the board according to the changes specified in the Qubes manual for the game to run properly.

I can verify that the main harnesses are the same across all 4 games (dual pc10, PO, SPO and Arm Wrestling). The control panel portion is different for each — only PO and SPO share the same control panel harness. Dual PC10 requires an extra 20 pin harness that connects to the PCB and then up...

Both DK3 and Popeye uprights use the same later style CP molex so they will mate up just fine. The issue will be connecting the coin/service/counter since DK3 was designed to plug into a DK/DKJ. Some of them have the adapter pieces on there to convert to the later molex. Only other issue will...

It's hard to tell from the pics, but I don't see the pink/red wire in that harness of yours (it's the signal ground wire for the gun). I sent you a PM as well.

The stock Vs. gun harness gets installed into the Player 2 section of the harness. It definitely looks like you have a little wiring to do before you can get it back into shape. Including adding a connector back to the gun side of the wiring (if you want to make it stock again). Here's the...

Unfortunately, that early version of the light gun is non-serviceable. There is no way to open it up without cutting open the actual gun and destroying it in the process. The inside components are also covered in insulation if you do get that far to peek inside. You can check to make certain...

The Fire button should be connected to A9-P2-8 and follow all the way through to the edge connector (A1-J1-21). Usually it's a blue wire coming from the joystick to the control panel molex.

The interface board does have a separate ribbon cable, but that only controls the Spinner, not the joystick. I would start by tracing out the Fire button wire and make certain that the ground wire for the joystick is also attached.

Please delete. Wrong section.

SMB3 should work normally with the Reset button. I've had numerous SMB3 carts that definitely work with the Reset. In the past I've noticed the exact same glitch depending on a specific lineup of games on the main PCB. It could be an issue with that particular SMB3 cart or it could be an...

Also, I forgot to mention that I tried both scenarios with and without the SMB Free Play/High Score Save mod. There was no difference when using the stock roms or with the modified rom.

I had some time this afternoon to test for the flicker using one of my Red Tents. I was able to now see the flicker during each of the tests. I used two different fully working Rev. 04 main boards and tried SMB on both the 1-2 and 6-8 sides. On the one board, I paired Dr. Mario with SMB...

I guess I'm confused as to how you could test one side on the opposite side it was intended to be used on? Did you burn a full set of 12 different roms or did your set only have 6 rom files? PM me if you need a set of known working rom files.

I just burned a set of Balloon Fight roms a couple days ago and experienced a similar issue. My problem was that one of the eproms was slower than all of the rest (same brand/type of chip, but the speed was different). I swapped out that one chip to make the speeds match and everything then...