Search results for query: *

  1. FS:GO7 monitor chassis

    Go7 I will take it for 30 shipped

  2. For Trade: DK Jr. kit for a DK3 kit

    Dk3 I have a working DK3 that I would consider trading Mickey Warren 404-425-2622

  3. First cap done, but still no picture.

    ok, tested everything and all looked ok except R908. Tested R908 while in circuit and had no readings (resistor read 47 when out of circuit). Bought new resistors from RS (47 ohm 1/2 watt 5%) installed it and replaced X701. plegged it in and had fireworks from R908. I removed X701 again and...

  4. First cap done, but still no picture.

    Do I need to do all of these checks and get the X701 back in before I make any adjustments ?

  5. First cap done, but still no picture.

    Thanks for all the help from everyone. I am learning. Removed the Transistor from X701 (if this isn't needed why is it there) Now I have a picture on the screen but it is real skinny and a little to tall what will correct this? Terrible hum bar on this also. I have the fuse blocks to change...

  6. First cap done, but still no picture.

    Thanks everyone for all the input. Checked the resistors- 220 ohm was at 207, 2 ohm was at 2.5 Will get som pictures tonight

  7. First cap done, but still no picture.

    It is a G07-CBO.Still has the sticker on it. I took the c904 cap off of a broken board and put it on this board, But still no power or picture.

  8. First cap done, but still no picture.

    Checked R1 and had no DC power. I was grounding to chassis frame. Is this correct ? Found the fromm flow chart and trying to Change the C904 Capacitor now.

  9. First cap done, but still no picture.

    I have checked these things now. Power is at board Mica was installed on HOT and is not grounded Fuses are good Where is the R1 resistor located? Where can I find a good schematic. Interlock is working Sorry if these are simple ?'s but this is my first attempt Thanks for any help

  10. DK3 to DK swap

    I have a DK3 machine and was wondering if a DK board would be a straight swap in it? Looking for a DK board also.

  11. First cap done, but still no picture.

    First cap done but no picture, still new to this and have no idea what to look for. This chassis came out of a super Pacman that was playing Blind. I put in a DELUXE CAP KIT AND FLYBACK from Bob Roberts. Checked everything with a meter for continuity and shorts, all ok. Took the chassis out...

  12. Cleaning boards?

    I have read where people clean the PCB's , Just wondering if you can clean the Monitor chassis the same way? Soapy water and brush ? Or Dishwasher ? (Would have to fix it before I fixed the board tho)

  13. Removing a flyback ??

    Ok, Thanks, Looks like new tools for tomorrow.

  14. Removing a flyback ??

    Will the 30 watt be ok for everything or still use the 15 on the other caps?

  15. Removing a flyback ??

    Trying to do my first cap kit. What is the easiest way to remove the flyback ? I am trying desolder braid, but it is taking forever to get all of the solder off. Thanks for any help

  16. New monitor needed

    I went with the vision pro 19 "

  17. New monitor needed

    Ok, Just ordered 2 Deluxe repair kits and also ordered a new Monitor from HAPPs. The new monitor will be going into a cabinet with a new PS will it also need a line filter? Thanks Mickey

  18. WTB--Original Donkey Kong Board set

    Looking for an working original Donkey Kong Board set

  19. New monitor needed

    New to all this. So if I rebuild the chassis the tubes should still be ok, one has bad screen burn but the other looks fine

  20. New monitor needed

    OK, I am going to order the Deluxe rebuild kit ($38.00) from Bob Roberts. I have 3 here that need it. If i rebuild a known working chassis and try it on the tubes that i am not sure work, will there be any chance of damage to the rebuilt chassis ? Don't want to fry it.
Back
Top Bottom