Search results for query: *

Hi I am looking for advice on my repro board, specifically the graphics ROMs 109 at 6L/M, 110 at 4E and 111 at 4D. When I populated the board I checked every resistor with a Fluke multimeter and IC with a tester was fine before fitting. When powered on it passes both ROM and RAM checks that...

Please let me know if you have the following spare inductors to sell me for my repro board. I am trying to get as original spec as possible with cylindrical inductors. Atari Part No. Supplier. Part no. Part Info. 141007-001 J.W. Miller...

This has been raised a few times previously on KLOV. After recently revisiting my improved Free Play ROM hack for Food Fight where I added blinking LEDs as per other Atari games I was asked to look at adding the same for Marble Madness. This game already has a Free Play mode that works well...

I am looking to buy an original marquee with the striped shirt on the boy if anyone has one. No preference for translite or glass, US postal address available. Thanks

I need a Missile Command cardboard bezel either repro or maybe I could make one. I messaged Joey Cuda a while back but not heard anything. Is there any site that has illustrator or pdf outlines of the Atari bezels?

If anyone has a donor chassis and is willing to part it I am looking for the grey rubber boots that cover the wires to the focus block. Please PM if you have any spare Thanks

I watched ”Louis Theroux“ on BBC this evening where he went back to the G.W. Zoo once owned by Joe Exotic after 9 years. Now owned by Carole Bakin, there are no animals left and everything in the park is run down. Joe’s old house is a mess and a previous thread mentioned it but it is still...

Hi I need to rewire to the S1 to S5 connector and tried molex 02-06-1103 but they are too long. Does anyone know what the 0.5" female pins are that are inside this connector that also is wired to the the neck board. Thanks

I am in need of some of the chassis G07 transistor insulators but cannot locate them. They measure about 5/8” across the diameter. I did try the TO-3E that has a 12mm outer diameter and a 7mm inner plastic piece but that was just too big to fit through the chassis hole. Does anyone know the...

I have a G07 chassis that has been working fine but now has vertical collapse. Fuses and B+ are ok. It had one of the older white types of 68r 2w fusible resistors and I could see there was smoke. As it was dead I replaced it with one of the newer Welwyn types and this also smoked and...

Hi I am looking for the following parts Chassis pin header marked S1 to S5 Neck board plug that goes into the header S1 to S5 pins Yoke plug that goes into header pins Q1 to Q5 (multiple needed) Thanks for looking

I just installed its first cap kit in my G07 and all is working fine. Is it best practice to always replace the flyback as well just as a precaution?

I had an issue with my Tapper G07 where the game was fully working but the monitor would not switch on. I noticed it had the original caps so did a cap kit but it still did not switch on so I checked the voltages and found it was going into HV shutdown. Following the flowchart I pulled...

Hi I have a 19" Vision Pro monitor with this Chassis and the picture is great with nice colours and black areas with no screen burn. After about an hour of being switched on the black areas are slightly less black as if the brightness has been turned up a little. Will a cap kit fix this?

I recently got a Star Force PCB and as I like to have a free play setting on my cabs and boards I decided to create a free play mod. The game I have is a Star Force (encrypted set 1) PCB using the 315-5069 encrypted z80 CPU. The original PCB has various coin settings using bits set on DSW1...

As per the title, please let me know if you have the metal plates that separate the 3 PCBs for sale Cheers

Although Food Fight has a free play mode that can be set using the dip switches, once set you no longer see the fancy attract mode and the high score table is not displayed. With no prior assembly knowledge I decided to learn a little 68k assembler and fix this problem by hacking the roms to...

Hi My coin box, wire holder and bolts are missing and want to get my Tapper back to the original spec. There are different midway boxes used of different machines so I would be really grateful if someone could post some pics of their holder and coin box. Thanks for looking

As per the title, Atari part number is A037430-02 Thanks

As per the title, I will pay a good price for a NOS or fully intact one