Search results for query: *

This cap is not available anymore. You have to make it yourself.

yes they talk about the one with 4 caps in one. I ordered the replacements caps but since I am happy at this time I will leave it as is. Thanks for your help

I use this one and it works well but it wont fix a pot if it bad. https://www.amazon.com/dp/B07F8YZS7N?ref_=cm_sw_r_cp_ud_dp_5SMFQC18X46GVXWYZ8JW

I forgot to say thanks to you guys for your help.

Ok I have a perfect picture now. It was the video BIAS adjustment I could not get the 45 volts out of it but I got about 19v for some reason it jumps up to 110v if you move it just a little bit from the 19v setting. I am very happy for now so I am going to go with if it ain't broke don't fix it.

I did do that. I forgot to mention that in the post. I also forgot to mention that I did test for 75v and that was good. It looks like if I leave the on the bottom of the screen gets better. I'm leaving it on to see if it goes 100 percent.

I have a Space Invaders that I am bringing back to life. So far everything in it needed repair. I am up to the last problem and am stuck. The monitor isn't showing the whole picture. I would say the least bright pixels. I will post pictures. If I move the contrast pot back and forth the whole...

Okay I got it to boot but I have more problems. It looks like I am missing most of the x side. I have some pictures so maybe someone has seen this before. First picture is in test and the second is in game mode.

It was the VECTOR ROM. Self test was no help though.

here are some pictures. It won't play a game. It looks like it resets video and it's like a lightning bolt across the screen. Let me know what you guys think. I think my analog section is good. Maybe counters?

I am at another point that I am stuck. Program is resetting until I lift pin 1 on L6 (DMAGO) I don't know what is the best way to troubleshoot. Should I leave the pin out and prob around or should I put it back in. I think out is the way to go but want to ask first. I think when you have...

Wow thank you for your help. I did what you said in a different way. Working back from the reset button I had all IC marked and went two the output and pressed the reset button. I got to IC E6 74LS08 and the output was not high or low and no change when reset was pushed. Replaced IC and it...

I have a pain in the asteroid board. If you put the game on red lights on no reset just stay low. I replaced all RAM, ROM and CPU sockets. All RAM, ROM, and CPU tested. If I put 5v on pin 40 game will play with graphic problems. I lifted pin 1 of L6 (DMAGO) still stays LOW. I dont now what to do...

Your welcome and post your results. I'm glad you found this useful.

Just an update on this. I had an extra power supply board to try so I tried it and it worked high score was saved. The voltage of 8.2 was about 8.3 on this board but the 12v for the coin door and marquee was missing. I found a open resistor and repaired the 12v. The voltage dropped to 7.8 and...

I have two board sets of Omega Race and they both don't save the high score. This has been like this for a while but I always wanted to fix it. One of the board's is a repo I built so all new parts. I saw the file with the voltage table and everything looks good except lower voltage because I am...

That's exactly what I have. I checked it out 10 times. I am gonna jump out dip 6 just incase that it's not working. I did a continuity test and it was fine. I also don't see R11 in the parts list. Maybe R111 is the right one.

I want over everything and it still resets. I have pin 5 going to pin 20 I think this is the reset mod you said to check. I was wondering at this point what value would you recommend for R11. It resets after a few power on and off. The circuit is working though. Let me know what you think.

I did make it myself I didn't even know that it was available as a kit. I will go over all the things that you mentioned. Thanks for your help.

Hi I installed this awesome upgrade. I am having a problem with it. It resets back to zero like every four or so power downs. The battery is good so I don't know what else to check. I was thinking of soldering the dip switch closed maybe it is bad. I really like the idea of it holding the high...