Search results for query: *

Asking what I paid a few years ago, $2500 $2000. Since purchasing I cleaned out the whole control panel area, repaired the volume control, and repaired the force feedback joystick. The original tubes had some really bad screen burn and I tried replacing them multiple times but couldn't get them...

This has had a few parts replaced (pots, deflection IC) and is now looking really nice. I also wasn't able to find any burn-in anywhere. Pick up in or around Apex, NC. Asking $200.

Tested and working Taito cute-em-up. Asking $160 shipped. US only

Both boards are working fine. Snow Bros is the JP release. Sky Soldiers: $110 shipped Snow Bros: $175 shipped (SOLD) US shipping only.

I've been trying to swap the tubes out in my Star Wars Trilogy and it's caused me so much grief trying to source the right tubes and get them working. I'm at the point I want to do a projector swap so I can keep the 4:3 aspect ratio. I've seen numerous other projects involving the Sega Megalo...

I've got a K7000a chassis with the telltale dual-wire flyback and at first glance it looks like vertical collapse because of the single line. But in other monitors I've seen with vertical collapse, you can see the single line change colors as the game plays. In this case though, the line never...

I've hit a wall on this board now. Right now on power up it will generally give me a screen of garbage or various error messages ("error 85"/"ill instr"). So I suspect it can't load the main code. When checking all the control lines I see that of the 4 ROMs for the main code, 2 of them have...

My SWT DLX had some pretty bad burn-in on the tubes, so I found a local Toshiba 50" 4:3 RPTV (2001) that worked fine. Following the instructions from the very helpful Youtube video, I replaced all 3 tubes. There were no issues encountered and I reused the original yoke and rings from the burned...

My Golden Tee 2004 is using a compact flash HD replacement and worked fine the few times I played it. I put it in a box on a shelf in my basement for a few weeks and then brought it back out to play. I noticed that the game would go through the attract sequence for quite a while, but as soon as...

I just picked up the deluxe version of STW Trilogy and I'm having an issue with the force feedback. When I power it up, I see Error code 21 on the drive board. Looking in the manual it says the problem is with the Y-axis. The joystick will move left and right to center itself, but not up and...

I picked this board up from another forum member and it's been passed around before. I replaced the missing parts (CPU/ram) and it boots up to garbage. I turn the speaker up and hear the fast click of the watchdog. I check the program ROMs and they all match MAME but I see they are the 32 pin...

I've got this Nastar board that has been through a lot. It had a horrible bow in it that caused two of the big custom ICs to half pop off. After straightening out the board and soldering those chips, it was then stuck in watchdog reset. Turns out that the bow caused 4 or 5 of the CPU pins to...

I'm working on a Golden Tee 97 and I suspect there's a problem with the PIC16C54 on the video board. Am I right that it is something that has to get programmed? I didn't see this dump included in the MAME set, but looking at various ROM news shows that this chip was successfully read. What are...

I've got a Taito Superman that was missing the daughterboard when I bought it. I understand that the daughterboard was used to allow smaller ROM chips, but I used 4 chips of larger size to replace it. The problem I've discovered is that the headers used don't work well for ICs, they are actually...

I've acquired some PCBs and one of them has a serious bow in the middle which caused a couple of the large surface mount ASICs to pop almost completely off. I'm concerned that if I screw it down to a board to flatten it and resolder those chips, they will just pop again when I remove it. Is...

Has there been any more work done trying to dump this PAL for Raiden 2? I've got a couple boards with this chip socketed so I'm able to verify that one of them is bad. But as far as I know it's undumped. In lieu of that, does anyone have a spare available?

I recently bought a Desert Assault that isn't booting up. I just noticed that a PAL at location 10D is missing. I couldn't find any PAL dumps around, but I've noticed a couple PCBs sell recently. Anyone have access to it and can provide a dump for that PAL?

I picked up a broken Strikers 1945 from another member on this forum and I'm trying to work my way through it. When it powers up, it shows a successful RAM test but with a slight about of graphical issues on the black background. It then goes to a distorted gray screen and/or reboots. I checked...

I picked up some defective Raiden 2 boards and I'm kind of spinning in circles with them. One seems pretty dead so I've put it to the side. The other boots up to just some garbage on the screen. It doesn't look anything like the game, just random pixelation and it doesn't appear that the garbage...

Prefer US bios, but JP would work too. Don't need any cables with it.