Search results for query: *

Looking for a source to buy some joystick centering grommits. Right now I need a couple for Robotron leaf switch joysticks & a plastic base nintendo joystick. They are both the same....the square metal plate with 4 holes & the rubber grommit with metal bushing in the center. I contacted Mike at...

I have a 19" Kortek monitor with the remote board purchaced from ArcadeShop earlier this year> I got this to put in the Multi-Williams project I've been working on. The colors wash in from the bottom corners. At first I thought it needed to be degaussed, but several tries with a degaussing coil...

SSIA....looking for a tested working Pole Position board. You can PM me or email me at: davemclellan AT comcast DOT net (take out the spaces & replace the @ & .) Thanks

Looking for a chassis or neckboard. Restoring a Pole Position. The neckboard on mine is cracked.

Looking for a complete DK JR wiring harness to get a jammatized. DK JR cabinet back to original

Does anyone know of a source for the neon lamps found on the B/w x-y deflection boards at NE501 , 502 & 503. They are listed as: Lamp Neno (GE) 5amp. Bob Roberts doesn't have them.

I aquired a G07 that was plugged directly into house current (no iso xfmr used) this weekend. It was working prior to this, but had a problem with the convergence. What are the parts that will most likely have to be replaced. I'd like to at least get a starting point , to get it to power up, so...

Guaging interest: NOS onopened 19" B/W vector CRT's Trying to get an idea if there'd be any interest in NOS new in original box 19" B/W vector CRT's for G05-802 or 19V2000 monitors. Probably in the $150-$165 range shipped in original boxes w/ insurance. I beleive they are a Philips CRT. I'll...

19V2000 HV problems I have a V2000 that came out of an omega race running in an asteroids game. Game board known to be good. I'm not a newbie to the hobby, but a newbie to working on the vector monitors. I've read the FAQ & Guide forwards & backwards a couple times, searched the monitor forums...

Ok, I got a new HV unit, looks clean & recapped. I cleaned & dried the HV diode & connectors & springs & reinstalled. I changed the 4 transistors on the monitor frame. Soldered solid copper wire at R100 & R101. Installed Bob Roberts cap kit on deflection PCB & replaced bad fuses at F100 & F101...

SSIA Looking for a working Asteroids PCB or 2 to finish up a couple project games.

I have a Sanyo 20 EZV I want to use to restore a dedicated DKJR back to original, unfortunately I don't have another working one kicking around to refer to. The yellow & white wires from the yoke PCB at points EG & EH were hanging loose on the chassis PCB, I resoldered to the posts on the...

looking for a high voltage PCB or just the HV xfmr for a 19V2000

I'm only familiar with discharging color rastar monitors with a screwdriver, wire & alligator clip. I have to discharge a couple 19V2000 vectors & understand I should use 1000K resistance between the screwdriver blade touching the anode & the alligator clip touching the monitor frame. Can I take...

I mistakenly posted this in the other technical section....sorry for the dulpicate questions & waste of bandwidth. I picked up a untested 19V2000 for 1 of the asteroids projects I'm working on. I have a working asteroid deluxe with a working G05-802 monitor in it I plugged the untested 19V2000...

I picked up a untested 19V2000 for 1 of the asteroids projects I'm working on. I have a working asteroid deluxe with a working G05-802 monitor in it I plugged the untested 19V2000 into the deluxe cabinet & am getting an orange glow at the back of the crt neck. 1) the connector is comatable. Is...

Capcom Bowling conversion 3" trackball wiring HELP I have a 3" capcom bowling trackball without wiring harness. I am making a CP to go on a jamma wired taito cabinet that currently has a Contra jamma PCB installed. I have 4 pin molex connectors to plug into the 2 molex headers on the trackball...