Search results for query: *

My Mario brothers is not working. I get an error screen when I turn the machine on. When you push player button the game play screen comes up, but is locked and you can't move Mario. I've attached a couple of pictures. Any ideas would be appreciated.

I put a new board in my video slot. It worked fine for a short while and then the screen turned to 100s of small, colored squares. One of the chips is quite hot. Is this a bad chip. If so where would I get one. It is a LUCKY 8 LINES 8 LINER PCB.

Does anyone have details about a large collection of pinballs in Cando North Dakota. I'm heading that way and would love to see it. I saw an old post from 2005 on a different forum that talked about it.

I purchased this game at an auction. Turns out someone took cpu part so all I have is monitor and cabinet. Does anyone have advice on who made game, where I could find the cpu, or where I could find replacement game. It looks like it is a video slot machine from the graphics. Thanks for any...

My High Speed has been working fine, but now a problem has started. When I turn it on the pop bumpers and the jet bumpers at the bottom of the play field don't work. After awhile they begin working, its like they have to warm up. I've checked all the fuses and they are good. Anybody have an...

I have an old UpScope video game. It is fairly unique, made by Grand Productions. It runs off of an Amiga Board. The game turns on, but it immediately goes to the settings screen, where you set various options. I can't get it to go to the game. Does anyone have ideas on what I should do. I...

I have a Ms Pacman cocktail and a tigerheli video game and neither will hold a high score when I turn it off, although it is still plugged in. I've looked for a battery backup, but can't see one in the game. Any ideas?

I just bought a 1966 Williams full house. anyone have a parts manual they would like to share. Thanks.

I have an Up Scope game made by Grand Productions. I recently replaced the motherboard. It uses an Amiga A500. Now it comes up, but seems to be stuck in a main menu that allows for adjustments of the game, but I can't get it to go to the game itself. Any ideas on how to get it to game mode.

I have a Williams High Speed. Lately I get no sound for a few minutes and then it comes on. Once it is on I seem to get more than one sound effect at the same time. Any one have suggestions on what is going on. thanks.

Thought pin fans would find this interesting. The Idaho Lottery currently has pinball scratch tickets out. Link to my site which has a photo of one.

I picked up an old Darling EM. I have cleaned all the switches, checked fuses and it won't run. When I start machine the score motor runs, resets score reels and thats it. No switches work and flippers won't work. Anybody point me in the right direction. I kind of assume I have a bad relay.

I found an old bally arcade game, heliattack. the monitor is going. Anywhere a person can find one reasonable.

I am missing some parts on an under the playfield "single" flasher board on my High Speed. Not sure if it is a diode and resistor or 2 resistors. If someone can tell me how to attach a photo I could post that. When the playfield is tipped up the board is in the lower left corner. Any help...

I have a Williams High Speed I've been working on. Question, the flashers on the left side don't work, rollover switch on bottom left lane doesn't work and one target on two of the target assemblies are not scoring. Anyone give me a clue where ot start looking? I have the Marvin guides, but...

I recently acquired a Williams High Speed and have started cleaning it up. Question, on the left side near the flipper is a ball kickback coil. It appears the end that strikes the ball is broken off. What goes on the end of the kickback rod and what makes the coil fire. I have checked the...

I recently ran across a rock tumbler on ebay that I bought. Anyone have some experience in using them to clean up metal parts? What media do you use? Plastic, glass, etc.

I can pick up a Williams Aztec and a Bally Night Rider for around $400-500 apiece. Anybody have opinions on a good price. They work well and have little wear. Need rubbers replaced and playfield cleaned up. Appreciate your opinions.

Has anyone heard of a 1978 Bally Fireball Professional Home Model pin? I found one pretty cheap and in good condition. It seems to be 3/4 size. Never ran across this before. Would like to hear what others have to say.

I have a chance to pick up a 1983 Bally Gold Ball that is in pretty good shape. Price is very reasonable. Anybody have an opinion on the game, fun to play? I may get it, clean it up and resell. Appreciate your thoughts.