Search results for query: *

After recapping a G07 I discovered that with the degauss coil connected on start up, F902 would blow. I replaced the fuse and tried again this time with the coil disconnected—the monitor turns on, no blown fuse. I adjusted B+ to 120V and the picture looks great. After a couple of fuses and...

Still looking for a tube bump.....

Wednesday bump. Just need the tube.

Bump for Pacman cocktail....

Thank you, that is great information and very helpful!

I've noticed that some of G07s have a metal shroud over the back of the tube and some do not. Is this for shielding purposes? I've seen cocktail tables with and without this. I just want to make sure I get the right one.

I think I should be able to use the existing cocktail monitor frame and swap out the dead one with a replacement. So I'll just need the complete monitor.

Looking to replace my dead monitor (damaged tube) in my PacMan cocktail. Prefer something as burn-free as possible :) Please PM me if you have anything. Thanks.

I don't mind making adjustments if need be. Actually the sad part is I HAD a replacement monitor a while back but got out of the hobby and went on to other things. So after a couple of years of it collecting dust I sold it a few months ago. Recently I discovered that my monitor's focus pin...

The monitor in the cocktail is a 19". I don't have a replacement yet.

Hi All, This may be a dumb question but I tried the search but could not find anything. Can I use a G07 monitor from upright or does it have to be one from a cocktail. Thanks, Robert

Sold.

Selling a G07 Burn-Free Monitor with semi working chassis. I bought this about two years ago with the intention of putting it into my Ms PacMan cocktail table. I placed it in there and it initially worked but as I was making adjustments I got collapse as you can see in the picture. I planned...

Sea Wolf Repair Begins and Complete! Before and After pictures. Damn this thing was dirty! That's some '70s funk right there.

Sea Wolf Repair Begins and Complete! I figured I would post this as a follow up since it has been quit a while. My Sea Wolf is finally restored (for the most part) and up and running so I would like to show it off.  Everything on this was gone through and addressed. Power brick was...

Thanks guys. Weird Voltages confirmed A3 PIN 11 = 1.594 V F4 PIN 11 = 1.57V Resistors A3 and A5 Ground to Resistor = 5.07 v Resistance D7 Pin 7 to Pin 10 = 2.79 M Ohm Resistance C5 Pin 7 to Pin 10 = 1.35 M Ohm Which is way too high. I looked at the section for checking the 12V and...

I finally had some time to continue on this. I adjusted the PS so there was 5 volts at the board. Still nothing. I took out the H ROM and still nothing. I downloaded the midway 8080 test document and followed the instructions in section 3.4.to test voltages Vrb and Vra several points...

So I tested the voltages at the 18 pin connector on the motherboard and got the following results: Pin 1 = 5V Tested = 4.89 v DC 2 = 5V Tested = 4.89 v DC 3 = 12V Tested = 11.81 VDC 4 = 12V Tested = 11.81 VDC 5 = -5V Tested = -5.03 VDC 6 = Reset (confirm valid) = .025 VDC I measured...

I tested the monitor using the composite connection method and could faintly see something going on. After about 30 minutes of knob twisting I got a pretty nice picture. So now I know the monitor works. I'll start testing the voltages and for shorts as suggested. -Robert

Thanks guys. I will do all of those tests and follow up. Regarding the composite video connection: So after I remove the 18 pin connector from the monitor chassis, I then take the composite video out from the DVD player using an RCA cable and connect the tip to pin 18 (video) on the chassis...