Search results for query: *

I'm looking at the schematic. I have a working game with this small issue. 2 bars on the screen I cannot for the life of me figure out where they are coming from. Any one got a quick suggestion where to target. I've only gotten luck fixing one of these but this wasn't the issue I had issues...

I'm in the search for an unmarried hard drive. I've tried numerous chd images with zero results. if anyone has one message me thanks!! --ron

I'm finishing up a new build of the aftermarket Warlords board. Does anyone know what I can use for the 90-7035 RAM @L8 and K8. thanks!! I got everything. This is holding me up.

I'm baffled on a issue I've been fighting on and off for a half year. figure now I'll see if anyone else has a insight what to check. But first the important information first. Known working ram set, all eproms check ok with checksums, new cables MCR switcher (arcadeshop), and all 6116 ram...

Does anyone have the rom for this? I don't wanna drill a hole in a door if you know what I mean... anyone have it and can share it to me that would be great.

I'm stumped on a X's and O's. I have a mpu board booted. but missing one section on the display. Anyone have an idea where to target the output phase on the board. I have this running on an LCD Composite to VGA adapter. IT also does it on a CRT so I know its not the lcd doing this.

Has anyone tried putting a WG 19v1001 in place? I got a m5000 which has no glow.. has me stumped. I got a bunch of working 19v1001 chassis. Just wondered. as for my m5000 no glow or HV. I suspect the q9. I ordered all three replacement transistors. -Ron

I have one I'm working on its a XM700... its wavy. it had a nice solid picture until I left it on more than 30 minutes. I've recapped most of the monitor. Anyone have a clue?

I have fixed numerous MCR board sets but I got one that's stumping me. Its in a Tron, I can see text just fine... Tron logo just fine. Background graphics ok. And moving sprites or the MCP cone on the attract mode is at the bottom of the screen. Advice on which section of the board to...

Just as the topic states. I get 5 bongs. I can't recall where the list is which tells me which chip is bad... Anyone know or have this list. Thanks -Ron

Just as the topic says.. Looking for buildings left and right. I have a center. Also looking for a plastic set.

Just as the title says. I'm looking for a set of hinges from a system 11 cabinet. anything from roadkings up to jokerz! If anyone has scrapped a cabinet PM me.

This one has me baffled. I brought this boarrd back from the dead. No ram errors now bad sockets changed. But the video is torn. I have replaced the DACs with new ones. Anyone else see this issue before? Also the monitor was rebuilt and does work well with a know working board.

I'm normally very good at MCR board repairs... just got another sound board going but to notice I got static still. I've noticed in audio test channels 1 2 3 are static where as 4 5 6 are almost perfect. I have a MCR switcher installed. Not original transformers etc. due to the tron cabinet...

I'm finishing a restoration... Starwars Atari Vector. It boots up great.. got a picture... every so often it flickers real bad.. it will sometimes freeze and then go back to the game looking normal as if it should. This is my fourth vector game I've restored and never seen this.. I'm gonna...

I've gotten a g05 bw xy monitor going...worked great... recapped it and everything. Just yesterday I get no picture... fuse 600 blew on me. replaced it... and the spot killer is off. great... no so great... I have glow and chatter.... but the ceramic resistor gets real hot.... and the picture...

I just got a Nascar arcade sitdown and its video when plugged into the vga port on my lcd is all washed out. Does anyone have a schematic for the Hikaru board set? I'm suspecting a video amp isn't working right... *I'm using a lcd at the moment until my monitor chassis comes back from being...

Does anyone have a cap list for this monitor... I got two of them and they are both shakey... so some new caps are in store for these.... Thanks -Ron

I have hunted all over the internet for solutions on troubleshooting a dig dug thats not booting. Both LEDs are lit and it makes a consistant tone. I've checked the eproms to find one bad... re-burnt it.. no change. I have changed the Big blue.. Checked the voltages.. they are all in good...

I want an option. I'm going to be installing my new sideart for my Tron. I've seen people say the wet method and those that do the dry method... I myself am leaning towards the wet application method. Who has done this.. tell me your thoughts..before I do my application. I'm in the process...