Search results for query: *

  1. perry1670

    WTB: Sencore CR7000

    Looking for a Sencore CR7000 preferably with the adaptors. If I even began to think about paying eBay prices I'm pretty sure I'd stroke out :)
  2. perry1670

    Help fixing my Fluke 9010a

    Let me be more specific: The Marian 6800/6502 pod is currently configured as a 6800. It fails Self-Test with code 00 When troubleshooting the board following the 6800 Pod Manual on page 5-9 it says to verify voltages which have checked out good. Then it says to READ@0FF0 while using the self...
  3. perry1670

    Help fixing my Fluke 9010a

    I recently picked up a Fluke 6800 POD to help diagnose the 6800/6502 Marian Pod. When powering up the UUT and hitting "Learn" on the 9010A I get CTL ERR 00000000 00000001. After reading some in the 9010a Manual - I believe this corresponds to a control line failure, with the 0s and 1's...
  4. perry1670

    WTB: Working Asteroids, Centipede PCB

    I'm looking for a working Asteroids and Centipede PCB Want do a some testing with my new SLICE and see how it does. I could use an AR 2 Regulator board for Centipede as well if someone has one laying around.
  5. perry1670

    Help fixing my Fluke 9010a

    My apologies for the confusion on this. Correct: Mainframe <-> Marian 6502 Pod; Pod self-test socket <- UUT Cable; Pod Self-Test jumper installed. Test is: Power on Mainframe -> displays power on message -> press Bus Test. What is the result? 6502 Fail 00 Now, SET-TRAP BAD PWR SUPPLY? NO...
  6. perry1670

    Help fixing my Fluke 9010a

    Test Jumper is installed above the self-test socket. The one thing that I should check is pin continuity on the Protection Circuits. They have very small pins and it is possible that one isn't making good contact with the socket.
  7. perry1670

    Help fixing my Fluke 9010a

    When going through the troubleshooting steps - (with all the appropriate ICs removed) I get BAD PWR SUPPLY - LOOP? - I can then go and SET-TRAP BAD PWR SUPPLY? NO and which leads to the CTL ERR 00000000 01111111 - Loop screen. I believe that is what I should be seeing. Unfortunately I do...
  8. perry1670

    Help fixing my Fluke 9010a

    So I got back in the Marian board troubleshooting: Problem still is failure code 00 on startup Verified all Jumpers were correct for 6502 Verified resistors and diodes were in spec (granted they are in circuit by still read good) Pulled all 74xxx ICs and tested - all good Swapped ATMEGA - No...
  9. perry1670

    Help fixing my Fluke 9010a

    I'll take a look at the schematics in the manual. Sorry I didn't realize that they were basically the same as well as double check the jumper settings. It does make it easier to compare as you posted the pics earlier in the thread so thanks for that.
  10. perry1670

    Help fixing my Fluke 9010a

    This is one of the aftermarket Marian Pods so the Schematics in the 6502 manual are not the same as what this is unfortunately. I'll go over into the other thread though and see what's happening. Thanks! Edit: Umm that is this thread :)
  11. perry1670

    Help fixing my Fluke 9010a

    It seems that a number of different threads exist for the various reproduction pods, so I"ll just use this one. Building some Marion 6502 PODs that I had laying around (has it really been 2 years?!) and am failing self-test with code 00. I'm seeing activity on the Data/Address lines so...
  12. perry1670

    FS Parts: Bally/Midway Sente Power Supply x3

    3 - Bally Midway Sente power supplies - untested $35 shipped
  13. perry1670

    PCB Identification/price check

    Unfortunately I wasn't able to garner much help from the forum but it's all good. Still not sure what this is JTT-012C mainboard with JTT-012 Color-3 daughter. Regardless, %20 percent has been donated.
  14. perry1670

    PCB Identification/price check

    A/G Converter A082-91411 - Omega Race - Midway Rock-Ola Exchange Unit 52240-A (jukebox) So That is most of the non Williams easy ones, now onto the harder ones I suppose. Little Daughter boards and whatnot, other then this one. JTT-012C mainboard with JTT-012 Color-3 daughter. I removed the...
  15. perry1670

    PCB Identification/price check

    To ebay they go
  16. perry1670

    PCB Identification/price check

    I'll apologize in advance if this is not the correct location for this post. So being more of a pinball person I have little use for the various arcade PCBs that I recently acquired. Some I can Identify, others I can't but I'd rather not just throw random PCBs on Ebay. With that my thought...
  17. perry1670

    WTB: CPS1 "A" board, or CPS1 Game

    Looks like i'm going to need a CPS1 "A" board, or a complete game if noone has a board they can part with. Let me know the price shipped please, and thanks.
  18. perry1670

    CPS1 Final Fight video/sound issue

    Yeah, the dips are set to have attract mode on. All i get is a an electrical hum out of the speakers. When the game is being "played" there is no sound either so the dip switches i believe are in the correct positions. I'll check the molex connectors again just to see maybe I missed something...
Back
Top Bottom