Search results for query: *

pipe clamps. what cabinet builders use. get them at any box store and buy 3/4 pipe to what ever length you need...

have a look at H-HOLD pot, i went through mine and couldn't get B+ proper, the h-hold was worn and was tough to track down.

i am exchanging the board with Andrew , as the traces are very fragile, and messing with it to much might make things worse and to a point no one will touch it. i have ordered everything i need for the monitor and will put my efforts there and a freshen up of the cab and a closer inspection of...

P2K "write-able" programmer daughter board. Going to germany soon as it has WB ( partial) on it and i will never attempt a project that size.

PM sent about this

Was probing a bit today , A2 was as far as it would test , prober B4 M2 , pins 1,2 both has some activity, went to F2 . Pin 2 was dead . Held probe to pin 2 , hit reset and pin 2 (F2) went low then high and A2 passed test and Hanging test on A1 now. I think F2 is no good.

i will look over everything under a magnifying glass today, C2 was chipped/damaged, Xbip was bent / legs touching, one broke, the Q infront of xbip was bent legs touching also so chances pretty good there is more. yes well cleaned/deoxit applied . roms were very dirty, cleaning them got the...

i have H2, J2, A2, and C2 sockets in place. went well no lifting issues , noticed C2 was cracked , one leg was broken from looks like impact. under C2 trace 6 was broken . those are repaired but no matter what RAM i try, A2 just will not pass.( i can use J2 to basic test ram) with probe , legs...

hold my beer, i got this

ok i'll try H2 and see how it comes out, yes i have a Hakko fr-300, and i have a Kester flux pen, i have never used flux to desolder before, i'll give it a try.

i bought a 40x illuminated magnifying glass today, i think i may raise them with thin stock cardboard just a wee bit . im going to clip and remove one leg at a time, i assume these are just as fragile with lifting as the williams boards are. toning out is a great tip , will do. im going to...

great advise!

will a 5006 work and do same as a 5004?

done with piggybacking, tomorrow i will grab sockets. the original AR11 had a lot of repairs done to it and was super cooked in places, ill post pics tomorrow. looks like they went through that and stopped there. my hakko wasnt working very well so i took it apart and cleaned it,it works like a...

Ram is from a working tatio board, will start to socket and test tomorrow after work. as i piggyback one, the behavior changes. the only consistant one is J2. i had a sinistar that would piss around like this with the rom board and finally gave up and shipped it off, i think i sent it to you...

i got it past the initial short low then high tone by piggybacking J2 . i can get it to pass up to D2 where as no matter what ram i piggy back it gives me the same, 8 short low followed by 2 long high. manual states only one long tone?? any ideas? FYI today it was giving me short low tone...

+5 foil lifted and touched +12, fixed AR11 is fine. piggy backed J2 and am now getting correct tones for RAM issues. i now have short "low-low-high-low" (A-2??) will round up more ram and plug away.

very short, just 1 1.2 second tones . i will look at the AR11 tomorrow.

i was giving a high pitch then low upon start up, now nothing again. i will probe again later.

i will i had to step back from it for a bit. the machine came with the manual and three fold out pages of drawings. i think i am going to take some time to study the flow of the watchdog circuit and understand what it is missing that is setting it off. i read in another thread that H2 & J2...