Search results for query: *

Does anyone have a parts list for the Shinlee EM201? Have found manuals, but nothing with a parts list. I am trying to identify C-423, R353, and a transistor on the chassis.

I recently purchased a D9400 with a power input connector for which I can't find a connector that is the correct size. It seems to be double the spacing size of a 0.156" connector as a 5 connector fits (with the 2 and 4 pin locations empty) but I am concerned about the power draw if I use this...

Hello. I have a K4900 monitor with a portion of the right side of the screen not showing a picture. This missing portion is still there when the picture rolls. Is this issue that can be resolved with a cap kit or is there an issue with the tube or the yoke?

Are there any suggestions for the best way to reattach the metal brackets that hold the glass picture tube to the monitor/chassis frame. Two of the mounts are broken off where they attach at the rounded corners of the picture tube, and I was thinking of trying JB Weld as a repair but wondered...

I recently purchased an Arachnid English Mark Darts 4500, but some of the bulbs may be burnt out. Does anyone know of someone who sells replacement bulbs? It is Part No 11-0013 Lamp with Socket in the manual, but I have not found anyone selling replacement bulbs. Pictures below show the...

I bought a K4900 chassis and yoke from ebay, and the yoke arrived as shown in the picture with a portion of the red board broken off. Is this something that i can just hot glue back in place?

Does anyone know if there is a replacement flyback for a Sanwa PM1718 19" monitor? Thanks.

Does anyone have a control panel hinge or a pair of CP latch catch plates available to sell for a Robotron/Williams cabinet? I am also looking for a pair of latch catch plates for the back door. If you have any of these for sale please let me know how much. Shipping would be to Newark, CA...

I would like a Sega/Gremlin, Zaxxon control panel without controls if possible. Extra holes in the CP would be fine. A control panel other than Zaxxon would work too as long as it fits a Zaxxon cabinet. Please let me know if you have one available. Thanks.

I recently purchased a chassis with yoke which was damaged during shipping. On the convergence ring, one of the tabs broke as shown in the picture. On the yoke, part of the fiberboard that the copper wires connect to broke off but the wire connected to this is still connected as shown in the...

I recently did a cap kit on the three monitor boards for an G05-801 monitor in an Asteroids and the AR1 board. Prior to the cap kits, I had been experiencing some vertical collapse in the monitor. After the cap kits, I am experiencing significant vertical collapse and graphical issues as shown...

Is the fingerboard shown in the picture from an Asteroids something that should be repaired or leave it as is? I had the asteroids board repaired may years ago, and the person who repaired the board removed solder that had been placed on most of the edge connectors by a previous owner and...

I am attempting to rewire a cabinet with .100 housings like found in many Midway cabinets, but I am having the hardest time getting the wire properly connected into the housing. Any tips for this? Pictured is the housing I am attempting to use.

I purchased a Mag-Stik Plus joystick and upon attempting to install, I discovered the mounting holes are not the same as a standard joystick (mounting plate is smaller that a standard joystick). For those of you who have the Mag Stik Plus, what creative methods did you use for installing the...

Nor Cal, SF Bay Area - Whole List of Cabinets for Sale I am located in the SF Bay Area and am looking to sell the majority of the games I have acquired over the past 8 years or so. Listed below are the games I have for sale. If any of the games interest you, please let me know. I am not...

Does anyone know where I can find an copy of the manual for Radikal Bikers or have a pdf copy that you can provide? None of the usual websites for manuals have a copy posted online. Thanks.

I have a CPS2 18 in 1 board that was working fine until one day when it just stopped working. When the board is powered up, the menu comes up but there is no game in the background nor after a game is selected from the menu, just a black background. Does anyone have experience with...

Does anyone have a working Double Play PCB by Cinematronics for sale? If so please, let me know. Thanks.

I have medium resolution K7915 monitor that has a red issue. Sometime it has red and other times it doesn't. The last time I powered it up, I turned the monitor on and it had red. I then started to adjust the contrast and brightness and then red was gone. I may have touch the neck board when...

One of the buttons does not work on my Spy Hunter, but I haven't been able to figure out how to disassemble the grips. I have removed the screws from the grips, but I haven't figured out how to remove the buttons from the grips. Do the grips separate in half in order to remove the buttons as...