Search results for query: *

  1. V1001 multi can cap need help with values/locations

    Also is the blank spot on that can cap where the 20uf250v cap goes? That was where I was going to put that cap on my chassis
  2. V1001 multi can cap need help with values/locations

    Ok so my symbols and values match your A/B/C/D. I don’t have the larger cap in the picture on my chassis, just the smaller one. Can you turn down the contrast to help with the focus? That’s what I did on mine.
  3. V1001 multi can cap need help with values/locations

    Ok so figured out… 200uf100v is square And 20uf200v is blank.
  4. V1001 multi can cap need help with values/locations

    Replacing the huge multi can cap c101 in a v1001 monitor and I cut the cap conveniently where the symbols are to tell you what value to put to what terminal. Looking at it my options are Triangle Square D (half moon) Blank Per the cap it looks like 800 uf 125v is “D” Also looks like 200 uf...
  5. WTB: Satans Hollow Joystick Insert

    i've been messaging rich @ this old game (rikitiki) on this and he still hasn't gotten around to it. Maybe if everyone out there shows some interest we could get a run going.
  6. WTB - Satan's hollow joystick/insert

    Everyone is sold out at this point. I’ve been looking since January.
  7. WTB - Satan's hollow joystick/insert

    I am looking for a satan's hollow joystick insert specifically, the one with the bird on it. If anyone has one pm me whatever your price is. I will also consider buying a whole joystick assembly if that's how it's for sale. Thanks, jim
  8. Joust to lcd - gbs 8200 board no signal

    Temporary conversion until I have some money to get another crt... anyways I get a no signal message from this. The board boots up and displays the logo so it’s working ok. I am using the 8 pin connector with this. Not sure if joust is an issue cause of positive sync. I have tried changing the...
  9. WTB: K4900 Neckboard

    Thursday bump.
  10. WTB: K4900 Neckboard

    Looking for one working K4900 neckboard. Preferably not cracked. pm me if you have one.
  11. Removing flyback to neck socket wire K4900

    OK. So the neckboard swap went perfect. Monitor looks amazing now. Thanks for the tips.
  12. Removing flyback to neck socket wire K4900

    Ok thanks. That connection didn’t look like much to me so I thought it was further inside the socket.
  13. Removing flyback to neck socket wire K4900

    Yeah that’s what I meant. So after the back cover with the two little tabs comes off is that it? Do I just unsolder it from there or do I need to remove more? Just want to check before I apply heat to that pin.
  14. Removing flyback to neck socket wire K4900

    What is the correct way to remove this? I have to do a neckboard swap and not wanting to break it. Can it be removed from the crt socket side or should I remove the side connected to the flyback control? Also does this connect via a butt solder of the wire to the control? I did a g07...
  15. K4900 won’t sync need help

    Btw this pictures are after adjusting the pic with the h shift jumper and whatnot. It was further off the screen before I did that. This is the best I can get.
  16. K4900 won’t sync need help

    I have a Satan’s hollow with a K4900 in it. The monitor has been recapped and looks great. However the closest I can get the hsync to sync it still has like an inch off the screen. I’ve tried adjusting the controls which haven’t really made anything better. Ps ignore my other post I didn’t...
  17. Wg4900 picture centering/Horizontal off issue

    Hi. So have a Satan’s hollow with a k4900 in it. The sync was off when I first got it. The wires for the neg sync connector were swapped causing the issue. then screwing with it I got it as best as I could which was horizontally off center by a few inches when I got it causing the top of the...
  18. Help putting f14 on freeplay with dead displays

    Can someone help me with how to put an f14 on freeplay? The 3 and 4 displays are dead so I can see the top saying freeplay but the bottom where it shows the setting obviously isn’t working. It says to hit the credit button (I assume the switch on the coin mech) and hit auto up. But I can’t...
  19. Replacing side art that's recently installed...

    Ok. It is Phoenixarcade art that I used.
  20. Replacing side art that's recently installed...

    No pics. The art is beyond help. Has a small tear in it and I'll just buy a fresh one no big deal. I just can't work on it in my basement so I didn't know if anyone had experience if you take off art that's only been on a couple weeks does it all come off or will it leave the glue and stuff behind.
Back
Top Bottom