Search results for query: *

  • Users: buxtonore
  • Content: Threads
  • Order by date
  1. WTB: Working Gorf board set

    Looking to buy a working Gorf board set. Thanks
  2. WTB: Working Gorf Rom/Ram board

    Hi, I’m looking for a working Gorf Rom/Ram board A082-91364-A000. Thanks, Tony
  3. GORF issue

    Does anyone know which one of the boards, and which chip would cause this? I am able to start a game but it ends in about 10 seconds and the ship gets bombed immediately. Also the controls do not work. Thanks
  4. WTB: Dig Dug Wiring Harness

    I have a Dig Dug that has a switcher in it. Inside the cabinet there are a lot of hacked wires, and has never really worked very well since I’ve owned it. I’m looking for the complete wiring harness to hopefully fix this issue and restore the game. Thanks
  5. Wells Gardner 19V2000 Blooming issue.

    I have a Wells Gardner 19V2000 that is blooming after about 2 minutes of powering on. The image doesn’t get larger than smaller. It gets larger and stays that way. I replaced the high-voltage diode, but I'm still having the same problem. R 100 and R101 are both 4 ohms. The first picture shows...
  6. K7000 Screen Issue

    I have A Wells Gardner K7000 that does not fill up the whole screen. I followed the Flow chart, and checked the B+ which was normal. I also checked the 2 Transistors Q4, and Q7 both tested good. Not sure what to look for next. Any help would be greatly appreciated.
  7. FS Game: Mortal Kombat (Michigan)

    Original dedicated Mortal Kombat. Overall the game is in really good shape. It Has had numerous upgrades. New paint, new overlay, new coin mechs, new locks, new T-molding, new coin door lamps, New sound pot, new marquee light, and the monitor has been completely rebuilt. Original side art is...
  8. Burger Time Stuck in test mode

    Hi, I have a Burger Time CPU that was having problems Sustaining power. The problem was remedied with two new ribbon cables, a new edge connector, and pins. I Installed all of those, and now my game is stuck in test mode. Any ideas what could be wrong? Thanks
  9. Burger Time Issue

    I have a Burger Time that needed a new connector on the main board. I just replaced the connector, and replaced all the old pins. When I power up the game R125 burns up. I checked all my connections, I replaced each wire one at a time from the old connector to the new one so I wouldn’t make a...
  10. WTB Working Gorf RGB Interface Board

    Looking for a Working Gorf RGB interface board.
  11. FS Game: FS Karate Champ Michigan

    Very nice Karate Champ. The Game was restored A few years ago, with new side art. The monitor was capped then as well. Does have some screen burn, but the picture is very clear. 800 or best offer. Located in Wixom Michigan.
  12. Star Wars Issue

    I have a Star Wars with a rebuilt K6100 monitor. The spot killer light comes on and stays on. It makes all the game sounds and it does play. However there is only a small straight line on the screen. I know the monitor works because I hooked it up to my tempest game. The voltages on the board...
  13. WTB: Wells Gardner K6100 Neckboard Connector

    Looking for the connector that connects to the neck board of the Wells Gardner K6100. Thanks
  14. Gorgar both led lights on the MPU stay on

    The Gorgar machine I have has both Led lights on, and it keeps repeating Gorgar on a loop. Sometimes when I turn the game off and on, it operates correctly for a minute or two, then it goes right back into the sound loop with both leds on. Any help would be greatly appreciated. Thanks
  15. WTB: Working Gorgar MPU board

    Looking for a working Gorgar MPU board. Thanks
  16. FS Game: FS Taito Cocktail Space Invaders

    Nice cocktail Taito Space Invaders. The original Toei monitor has been rebuilt, and the boards were recently serviced. $700 or best offer.
  17. K6100 problem

    I have a Wells Gardner K6100 that is playing blind. The screen is blank with only a dot in the middle. There is a glow in the neck. R100 was burned up, and I replaced it, but the Monitor is still not working. I installed Bob Roberts deluxe kit five years ago. Any help would be greatly appreciated.
  18. WTB: Working Galaga board set

    Hi, looking to buy a working Galaga board set. Thank you.
  19. FS Game: FT/FS Gyruss Gorf Karate Champ ( MI 48393)

    The games are all in very good condition. Gyruss has a new control panel overlay, The front of the game has been completely sanded and painted, and the sides touched up. Also a Cap kit was installed on the monitor. It also has a new fly back. 700.00 Karate Champ has been completely restored...
  20. MS. Pacman issue

    I have a MS. Pacman that has garbage on the screen. Does anybody know what Would Cause this? Thanks
Back
Top Bottom