Search results for query: *

  1. arcadeaction

    SOLD - PARTS Pi Position w/Rpi, SD Card and Steering Opto - New

    Here is an unused Pi Position board w/Rpi. Bought as a backup but haven't tried it as have both PP1 and PP2 boards that continued to work. SOLD
  2. arcadeaction

    Panic Park - Namco System 23 repair

    A Panic Park game has a video issue that is not a monitor issue. When turned on, the game will appear to be playing blind but have some rolling interference lines on the screen. Over the course of about 5min the image will fade in and become progressively brighter but still seem to have heavier...
  3. arcadeaction

    K4600 Width Coil Compatible with G07?

    Are G07 width coils actually compatible with k4600s? According to this old post, there is a statement that seems to say they are if you cut off the two support legs and install. Would be interested to know if this is the case. "Toss that junk Width coil in the garbage, and mount a GO7 one right...
  4. arcadeaction

    FS Parts: Capcom Bowling PCB

    Tested and powers up and seems to run. I did not test with trackball controls etc. $62 shipped to CONUS
  5. arcadeaction

    Centipede PCB - a screenshot of issue

    Currently seeing this double split screen with graphics issue. The graphics jump around. Game does not respond to start buttons (both are lit up) or go into test mode. Voltage on AR board reads about 5.08 and on game board about 4.68 on test lugs. Looking for some general pointers, thanks
  6. arcadeaction

    FS Parts: Data East Edge Connector Conversion Boards for Arcade Boards

    These boards are designed to run game boards of other manufacturers’ pinouts in a DataEast arcade game. Untested, sold as is and inexpensively to get them in a collector’s hand. $12 for both plus small flat rate box $10.50 shipping = $22.50 total shipped to USA destinations
  7. arcadeaction

    FS Parts: Tempest style spinner - Cyclone II USB

    For sale are some nice Cyclone II USB spinners designed in the fashion of an Atari Tempest spinner with same/similar mounting and spinner top with set screw, including hardware. A computer will see it as a USB mouse and it has wiring for two buttons with slide on connectors to go on buttons...
  8. arcadeaction

    SOLD - PARTS Mortal Kombat 2 Wiring Harness - Original JAMMA

    As shown, this original JAMMA harness labeled Midway Mortal Kombat 2 (MK2) looks complete as received other than not including the control panel harness. I didn't end up needing it for a restoration project. $80 plus 10 shipping to USA destinations Thanks
  9. arcadeaction

    Final Furlong 2 PCB or MSPM daughtercard

    Looking specifically for one MSPM daughtercard for Final Furlong 2 or whole PCB if you have one available or know where one may be purchased. It is Namco Super System 23 hardware.
  10. arcadeaction

    SOLD - PARTS CRT Rejuvinator/Restorer Sencore CR70

    Here is a Sencore CR70 unit as shown. Includes the adapters (which to my understanding are all of the intended ones it shipped with inside the box, including the universal adapter). The foam in the adapter storage compartment has broken down as is typical. The adapters still store just fine...
  11. arcadeaction

    WTB: Final Furlong 2 PCB

    Looking for a working Final Furlong 2 PCB. The PCB stack for each player is four boards, I believe, and they are jointly housed together in a metal shell.
  12. arcadeaction

    Which monitor chassis is this? A Sharp/Kortek?

    So far from research it seems maybe to be a Kortek or Sharp variety but I've not yet seen an exact photo. It is of about a 33" monitor. Photo attached, thanks More info: This post also has the same monitor (additional photos shown in their post) but they also had not identified it...
  13. arcadeaction

    WTB: Double Dragon PCB

    Looking for a working Double Dragon PCB, thanks
  14. arcadeaction

    WTB: Killer Instinct 2 - blue buttons

    Looking to pick up some KI2 blue buttons (1-6 etc). They have a thick ridge on them. Perhaps they were used in other games as well. Thanks
  15. arcadeaction

    Where is R80 located on a K7000?

    Where is R80 located on the K7000 chassis? I looked through the manual but did not match it up. Trying to locate as I'm reading that R80 can cause a vertical collapse issue where you see about 3-6" of a vertical image (which is what I'm seeing). It is a P538 K7000. Thanks
  16. arcadeaction

    K4600 video daughter card issue?

    What’s happening: Per the photo, there seems to be a type of power/brightness issue. The left side of the screen has a thick white bar and the remaining portion of the screen is visible but very dim (as if the flyback is turned way up for that first inch of the left side, but way down for the...
  17. arcadeaction

    SOLD - PARTS Street Fighter 1 Control Panel for HS-1 Dynamo style cabinet

    This is a six button per side original Street Fighter 1 control panel for HS-1 Dynamo style cabinets. This has an overlay that you will probably want to replace. I can take photos upon interest expressed. 125 plus shipping to USA destinations.
  18. arcadeaction

    SOLD - PARTS Mortal Kombat 2 Side Art - XL Arcade Version

    Here is an extra Mortal Kombat 2 side art for sale, still in the tube it was shipped in. -- SOLD -- It is like this which is 189 before shipping: https://xlarcade.com/products/mortal-kombat-2-side-art?variant=41451378344124
  19. arcadeaction

    Found or No Longer Wanted WTB: Working Pacman PCB

    Looking for a working Pacman PCB that does not have wires etc soldered to it, and preferably the original slow version. If you have a Ms Pacman PCB that may also be ok as I have ROMs from another board to convert to Pacman. Thanks
  20. arcadeaction

    FS Parts: SNK Mechanized Attack PCB

    This is an untested PCB as shown. Based on the board numbers it looks to be Mechanized attack and the ROMs are labeled with an MA. The pinout is not JAMMA. 75 plus shipping
Back
Top Bottom