Search results for query: *

  1. mattmatt

    paint code for dk blue

    Pretty sure that isn't the formula for Pro Classic. They told me this formula was obsolete when I checked at SW. Have you tried looking at the support piece inside and under the control panel? I pulled mine out and took it to get it color matched... But I would like the formula for Pro...
  2. mattmatt

    SOLD - PARTS Alan-1 Wells Gardner 6100 Deflection Board & XY Transistor Upgrade Combo -SLC UT

    I bought this but didn't end up needing it. Works great. $299 OBO I have 2 of these available. I bought these over at the Alan-1 factory but they didn't have boxes. These are $388 on ALAN-1. Buyer pays shipping. [For those that aren't aware, This is the deflection board replacement kit for...
  3. mattmatt

    SOLD - PARTS Spy Hunter Bezel and Marquee

    Marquee is excellent Bezel has a spot on the smoke screen that needs attention. $89 OBO + shipping Located in SLC UT Packed and ready to ship
  4. mattmatt

    Donkey Kong - Low green bias after installing 3DK Multigame kit.

    Yes. The issue was that my brightness was too low. I looked at all the color drives but didn't think it was the brightness. When I adjusted the brightness, everything worked fine. The HSS kit is great.
  5. mattmatt

    Star Wars - Missing certain sound bytes

    Hey People, Ok. So. New sockets on Sound ROMs, Checksums good - no change New socket on RIOT, no change Replaced the opamps @3c & 4c - Bingo. Thanks for everyone's help! @blown23t @andrewb @tstone @lilypad19
  6. mattmatt

    Star Wars - Missing certain sound bytes

    Ok. well. It is what it is. I will start on this and report back in a few. Thanks
  7. mattmatt

    Star Wars - Missing certain sound bytes

    Jaydon, Ok, finally got a minute to work on this. on pin 30, on the tones test, the signal goes from solid high, to the fast oscillating - It does this on 5d,4d,3d,2d, On pin 37 of 2D, for the quad tone test, it goes from nothing (not high, not low, just dead) to low during the tone generation...
  8. mattmatt

    Star Wars - Missing certain sound bytes

    Hey thanks. Ok, I re-read my explanation and it is not very clear. Initial state: Performed sound test and 2D isn't working - single ping - no 4 quad tone I Swapped 2D pokey to slot 4D. Now, the 2D pokey works in slot 4D but slot 2D still doesn't work even with known good pokey installed...
  9. mattmatt

    Star Wars - Missing certain sound bytes

    Ok, Sorry about the delay. I followed your advice and found that the the pokey in slot 2d works in 4d. Also swapped a known good pokey from another game into 2d. So it looks like the pokey is good, but maybe something to do with slot 2D? When I re-ran the sound test I only get the very first...
  10. mattmatt

    paint code for dk blue

    Ok. This paint sounds way better than latex. I asked my painter friend about it and he uses it on doors and trim on his high end houses. I guess it is more expensive than latex, but if the finish is better and saves money on a second coat.... Anyway. Do you have to apply a clearcoat after...
  11. mattmatt

    paint code for dk blue

    I think polyurethane is a good choice. I used some laquer that I had and it gave the paint a slightly yellowish tinge. Still looks good, but would show up on a side to side comparison with an unfaded original. So for anyone looking at this and considering latex I would avoid laquer. But if...
  12. mattmatt

    Star Wars - Missing certain sound bytes

    Thanks. I followed your advice (page 3 of troubleshooting guide (sp225)) and here are the results: Sounds played on 5D, 4D, 3D. But on the 2D test I got no sound After this, I continued grounding, and got all the sound bytes to work-- Including the Darth Vader and other sounds missing in...
  13. mattmatt

    Star Wars - Missing certain sound bytes

    When I run the test I don't get the sound for rom errors if that is what you mean. All the beeps are high. thanks
  14. mattmatt

    Star Wars - Missing certain sound bytes

    On my Star Wars, I'm missing certain sound bytes. Noticeable on first wave of tie fighters. Darth Vader bytes are missing. On trench, Han Solo missing. And some of what Luke says. Thanks for the help!
  15. mattmatt

    Found or No Longer Wanted WTB Galaga PCB - Tested & Working

    Please PM me if you have one. Thanks!!
  16. mattmatt

    SOLD - GAME PAC-MAN BATTLE ROYALE ARCADE MACHINE in SLC

    $3,900 Machine is in good condition, plays as it should. Fun for a game room or business, kids love it. It's set up for free play right now, but its easy to switch. Good earner. I can help coordinate with your shipper.
  17. mattmatt

    Donkey Kong - Low green bias after installing 3DK Multigame kit.

    Thanks, I messaged highscoresaves. I updated the description with my latest tests. check it out. Thanks!
  18. mattmatt

    Donkey Kong - Low green bias after installing 3DK Multigame kit.

    *** UPDATED BELOW*** DK board works great, (first photos) then I added the Highscoresaves 3DK Multigame with remix and my green bias goes away (Second photos). When I turn the green all the way up, I still can't get enough green. I checked the green bias pot on the neck and it reads at 2.2k...
  19. mattmatt

    What is Donkey Kong Side Art position? Can anyone tell me?

    Donkey Kong Side are Position UPDATED - I just measured some original side art off of a machine I just purchased, and from the top of the cabinet to the top of the side art is 4 11/16" (4 3/4" measured with the T-moulding in place). From the back of the panel to the side art is 2 5/16"
  20. mattmatt

    paint code for dk blue

    UPDATED COLOR CODE FOR DONKEY KONG (2025) -code for BEHR latex satin paint. This is a dead on color match from the inside of the cabinet piece. and way closer than the "Liquid Blue" people are saying to do. The above Sherwin Williams code is invalid, they changed formulations and equipment...
Back
Top Bottom