Recent content by fleetwood472

  1. SOLD - PARTS 4 soft reproduction 3/8 wico grommets

    I'm clearing out parts I was saving for future restorations I will no longer be needing. These are 4 softer wico reproduction grommets. Never have been used. Perfect for robotron, konami games and more. Asking $37 shipped. Thanks!

  2. FS Parts: NOS WICO 3/8 Joystick Shafts and used buttons

    Hey Guys, I'm selling some NOS joystick shafts and used wico buttons from a Simpsons arcade machine. Shafts are 3.5 inch with the exception of the plumb and light blue which are 4 inch shafts for xmen 6 player Asking $8 per joystick shaft plus shipping. Will sell the buttons with switches for...

  3. SOLD - PARTS TMNT Control Panel and Box with Vendetta CPO and Marquee

    Bump..

  4. SOLD - PARTS TMNT Control Panel and Box with Vendetta CPO and Marquee

    Picture of base with hardware

  5. SOLD - PARTS TMNT Control Panel and Box with Vendetta CPO and Marquee

    I have a TMNT control panel and base with hinge, retention chain, and locking brackets. It is from an original Teenage Mutant Ninja turtles machine but currently has a Vendetta CPO on it in nice shape and also includes Vendetta Marquee. In good shape and also has protective acrylic overlay...

  6. SOLD - PARTS NOS Wico Bat Microswitch Joysticks

    I have 2 NOS WICO Bat style joysticks. They have spring style grommets and microswitch bases. They are complete with dust washers and actuators. P/N on the box is 15-9897 05. Asking $60 shipped total for both. Thanks - Justin

  7. FS Parts: Reproduction WICO 3/8 Joystick Grommets

    Unfortunately all of my stock has been sold. I'll think about possibly doing another run. From the feedback I received it seems that most of the people loved the lighter grommets while some people preferred the slightly firmer ones. I'm assuming this is because even though the 4lb grommets...

  8. 6 Player X-MEN Restoration

    Nice work on the restore! From what I can remember I ran into a similar situation with the adhesive when doing a TMNT restore. From what I can remember either mineral spirits or acetone on a rag should take the remaining adhesive right off. I think I also used a plastic putty knife/scraper...

  9. FREE - Parts: FREE Golden Tee Control Panel Top From a Konami 4-player cab

    Hey guys, Bumping up a really old thread. If anyone is looking for one of these let me know. I still have this and would hate to throw it away if anyone needs one. Just pay shipping and it's yours. Thanks! Justin

  10. TMNT cab serial number sticker?

    RidicRick25 reproduced one for me when I was restoring my TMNT cab. That was about 5 years ago and he did a great job. Try sending him a message.

  11. Xmen 6 player progress on prints.

    Nice work man!

  12. FS Parts: Reproduction WICO 3/8 Joystick Grommets

    Hey guys, Sorry I haven't been on the forum much lately but I have now responded to all PM's. I am out of my softer 2lb grommets but do have some of my mildly firmer grommets available for $7.25 each. plus shipping. Thanks!

  13. FS Parts: Reproduction WICO 3/8 Joystick Grommets

    Hey Mark, I think some older samples may have gotten mixed up when I sent them into you for testing. My softest grommets for robotron were made at 2 lbs and my slightly firmer grommets were made at around 4lbs. I'll send you 2 more of the 4lbs just to see what you think when you get a chance...

  14. FS Parts: Reproduction WICO 3/8 Joystick Grommets

    All of this week's orders have shipped. I will also be doing another shipment on Tuesday of this week. Thanks again!

  15. WTB: 4 player coin door

    If you're using plans to build your own and end up routing it for 2 coin doors that were originally used I found this site has some available: http://thearcadeboneyard.com/coin_doors_and_parts/coin_doors.php The original tmnt used coin controls over/under coin doors.
See more
Back
Top Bottom