andrewb
Reaction score
16,955

Profile posts Latest activity Postings Media Albums About Post areas

  • Hi Andy, I have a Battlezone board that is not quite lining up correctly, and now is doing even weirder things. Any chance you still work on these?
    andrewb
    andrewb
    Yes, I do. Please private message me here. (This is the public message section.)
    My other question is Do you know where I can get a assembly for the HV diode? the springs and boot. I replaced mine using automotive shrink tube because when I got the machine the boot and springs was burnt and chard
    but it's starting to go bad. ship and text is getting large is size
    Hi Andrewb, you helped me with my Asteroid in the past. I wonder if you can help me. So only on player 2 one of the Asteroids on the screen you can keep shooting it but it doesn't move or shrink in size?
    Hi Andrewb, Out of my league , asteroids cocktail , cord ground pin broken off?, fuses F2-5 on brick P/S appear shorted to ground, disconnected monitor input P22 conn., short goes away , Found Z out from monitor possibly causing it, should i just change the connector?/ shot gun it. Possibly hot chassis scenario.
    Hi Andrew, any chance you do PCB repairs? I have a rev A Tempest set that needs some TLC (the previous owner did some work). I've checked all power and things look good, all clocks look good, the X-Y display on the scope is jumpy. I'm not in a huge rush.

    Thanks
    mj
    Thank you so much!
    What could it be? The thing is that the strange thing is that the light that used to blink before the start of the game no longer does so, it only lit up steadily when I put test mode, and I don't get an image either, just a dot in the center of the screen.

    sorry for using translator

    Thank you so much!
    Hi Andrew!
    My name is Javi and I'm from Spain, I'm currently trying to repair a battlezone Spanish version.
    The fact is that they share the same plates and I would like if you can help me with the orientation of the repair.
    Until now it played perfectly without image, but I don't understand why now when I connect I have no sound and the status light does not blink either.

    Thank you so much!
    Hi. Do you have an AR board for Pole Position by chance? Thank you
    andrewb
    andrewb
    Not at the moment. Pole Position requires two AR-II-01's, and I don't have any -01's. However if you have the original AR's in the cab, you can send them in to be refurbed. PM me if needed.
    I have someone looking to have their Major Havoc PCB repaired. It has two separate problems. One problem is there is a graphics issue on parts of the game. Do you repair these or do you know someone reputable that can repair this board? If yes what is the best way for them to contact you?
    Hi Andrew, I'm new at this and need help troubleshooting a wavy issue on my tempest.I'm disappointed because I wasn't having this issue until I decided to try and "bullet proof the monitor" The waviness is most noticeable during the level select screen. I have recapped all electrolytic and put in a arcade shop lv 2000. I also replaced all deflection transistors. Any help in the right direction would be appreciated!
    Hi. Do you have a paypal address? Want to send you a small amount so you can have a beer on me for helping me fix my pole position.
    Hello my centipede isn't saving high scores. I checked the 30V lug and only have 13V. Where would I go from here?
    Hello Andrew i am looking to have my AR2 rebuilt for my pole position i purchased a pi position board from Jason and would like to have this shopped out before i plug it in it has been sitting for years please let me know if you can do this and what the price would be thanks Bill
    Hello Andrew
    I Need help please. I have an asteroids cocktail table. I've had it since 1979. It has never been modified in any way and has the original Electrohome G05 monitor. Currently after power up the monitor goes dark after a few minutes. The game is still playing in the background. I've tried cleaning the edge connector. I've tried resetting all the connections on the monitor. Sometimes if I wiggle some wiring or the monitor connections the neck will glow and the tube comes back to life. The question is, will a cap kit fix this? Is it a bad soldier connection on the monitor board? Could it be a power supply issue. I don't quite understand where the monitor is getting its power from. I would love to talk to you about it. 314 941-3311. Im located in the central time zone. Call or message me please.
    Thanks
    Keith
    Hello, Looking for some Wico leaf-switch joysticks. Hoping you have 2 Robotron-style with 4" shafts and 1 tall, skinny 4-way. Would take a short, skinny 4-way if you don't a tall version. Thanks!
    Do you still repair Atari bricks? I've got one out of a Roadblasters that is blowing the main fuse. Thanks.
  • Loading…
  • Loading…
  • Loading…
  • Loading…
  • Loading…
  • Loading…
Back
Top Bottom